Difficulty
Moderate
Steps
11
Time Required
1 - 2 hours
Sections
3
- 1985-1988 Volvo 740 Jacking Front Wheels
- 3 steps
- 1985-1988 Volvo 740 Jacking Rear Wheels
- 3 steps
- 1985-1988 Volvo 740 Tire Rotation
- 5 steps
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Back1985-1988 Volvo 740
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
1985-1988 Volvo 740 Jacking Front Wheels
- Turn car off and remove keys from ignition.
- Place car in park (automatic) or neutral (manual).
- Engage parking brake.
Turn car off and remove keys from ignition.
Place car in park (automatic) or neutral (manual).
Engage parking brake.
1024
Step 2
- Use hydraulic jack on frame of car to raise car.
- Place jack head underneath frame of car.
- Only necessary to jack the car until the wheels are just off the ground.
Use hydraulic jack on frame of car to raise car.
Place jack head underneath frame of car.
Only necessary to jack the car until the wheels are just off the ground.
Step 3
- Place jack stand on frame of car and remove jack.
- Do no work under car supported only by hydraulic jack, serious injury or death may occur.
Place jack stand on frame of car and remove jack.
Do no work under car supported only by hydraulic jack, serious injury or death may occur.
Step 4
1985-1988 Volvo 740 Jacking Rear Wheels
Step 5
- Use hydraulic jack on frame of car to raise car.
- Place jack head underneath frame couple (pictured).
- Only necessary to jack the car until the wheels are just off the ground.
Place jack head underneath frame couple (pictured).
Step 6
- Place jack stand on frame of car and remove jack.
- Do not work under car supported only by hydraulic jack, serious injury or death may result.
Do not work under car supported only by hydraulic jack, serious injury or death may result.
Step 7
1985-1988 Volvo 740 Tire Rotation
- Pry off the all four hub caps by placing a small flathead screwdriver between hubcap and rim pulling the screwdriver away from tire.
- Pull hubcaps away from tires.
Pry off the all four hub caps by placing a small flathead screwdriver between hubcap and rim pulling the screwdriver away from tire.
Pull hubcaps away from tires.
Step 8
- Loosen each of the five lug nuts on all tires by turning them counter-clockwise with a 19mm wrench.
Loosen each of the five lug nuts on all tires by turning them counter-clockwise with a 19mm wrench.
Step 9
- Remove tires by pulling directly away from car exposing brake rotors.
Remove tires by pulling directly away from car exposing brake rotors.
Step 10
- Swap tires according to diagram.
Swap tires according to diagram.
Step 11
- Place tires on axels.
- Hand tighten the lug nuts with narrow end of nut towards car.
- Finish tightening the lug nuts with 19mm Torque Wrench to a torque of 63 lb*ft.
Place tires on axels.
Hand tighten the lug nuts with narrow end of nut towards car.
Finish tightening the lug nuts with 19mm Torque Wrench to a torque of 63 lb*ft.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Garrett Van Ruiten
Member since: 10/11/2010
54 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
Cal Poly, Team 3-28, Regan Fall 2010
Member of Cal Poly, Team 3-28, Regan Fall 2010
CPSU-REGAN-F10S3G28
4 Members
9 Guides authored
