1997 2003 Ford F 150 Alternator Replacement 1997 1998 1999 2000 2001 2002 2003 Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 - 2 hours

Sections

Alternator
8 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Back1997-2004 Ford F-150
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Alternator

Testing of the alternator output with the positive probe on B+ of the alternator. Even with RPM’s up to 2000 there is no change in output. It even appears as if the voltage decrease to around 8 V
This alternator needs to be replaced.

Testing of the alternator output with the positive probe on B+ of the alternator. Even with RPM’s up to 2000 there is no change in output. It even appears as if the voltage decrease to around 8 V

This alternator needs to be replaced.

1024

Step 2

Here is the alternator that is apparently not charging. First thing is to test it to make sure it is the problem.
B+ is the post where one can test the output voltage of the alternator with a simple multimeter.
The next step requires the engine to run. Keep your fingers, hair and loose clothing away from the engine bay. Do not stand directly besides the area of the belt. If it should snap it will act like a very damaging whip. Always stay to the side of it!
Set the multimeter to 50 DC Volt scale. Black probe to ground and red probe to B+ on the alternator. With the engine running the voltmeter should show around 14 Volts. On this alternator the voltage does not increase and sits somewhere around 10 Volts. Good indication that it needs to be changed.

Here is the alternator that is apparently not charging. First thing is to test it to make sure it is the problem.

B+ is the post where one can test the output voltage of the alternator with a simple multimeter.

The next step requires the engine to run. Keep your fingers, hair and loose clothing away from the engine bay. Do not stand directly besides the area of the belt. If it should snap it will act like a very damaging whip. Always stay to the side of it!

Set the multimeter to 50 DC Volt scale. Black probe to ground and red probe to B+ on the alternator. With the engine running the voltmeter should show around 14 Volts. On this alternator the voltage does not increase and sits somewhere around 10 Volts. Good indication that it needs to be changed.

Step 3

First thing is to disconnect the battery. I habitually only disconnect the negative cable.
This is the only part that may be difficult. The removal of the serpentine belt requires that the spring loaded belt tensioner gets pulled to the point that it no longer applies tightening pressure onto the belt. It requires a Torx T-50 which I did not have.
The proper way would be to insert the T-50 into the tensioner and then move that into counterclockwise direction to loosen
Where there is a will there is a way. Use a 15mm socket on the bolt that holds the idler wheel. Use the ratchet and move that into a counterclockwise direction. This will loosen the tensioner and the belt can now be removed.

First thing is to disconnect the battery. I habitually only disconnect the negative cable.

This is the only part that may be difficult. The removal of the serpentine belt requires that the spring loaded belt tensioner gets pulled to the point that it no longer applies tightening pressure onto the belt. It requires a Torx T-50 which I did not have.

The proper way would be to insert the T-50 into the tensioner and then move that into counterclockwise direction to loosen

Where there is a will there is a way. Use a 15mm socket on the bolt that holds the idler wheel. Use the ratchet and move that into a counterclockwise direction. This will loosen the tensioner and the belt can now be removed.

Step 4

Remove the regulator connector. Use a screwdriver or similar tool to move the clip so that the connector can be simply pulled up.
Remove the single wire connector the same way.
Remove the 10mm nut that holds the cable to the solenoid onto the alternator

Remove the regulator connector. Use a screwdriver or similar tool to move the clip so that the connector can be simply pulled up.

Remove the single wire connector the same way.

Remove the 10mm nut that holds the cable to the solenoid onto the alternator

Step 5

The alternator is held in place by three mounting bolts.
The first mounting boltis actullay a stud that also holds an air condition line. One the 15mm nut is removed, lift the line out of the way to reveal the second 15mm hex head to remove the stud.
Remove the 15mm stud

The alternator is held in place by three mounting bolts.

The first mounting boltis actullay a stud that also holds an air condition line. One the 15mm nut is removed, lift the line out of the way to reveal the second 15mm hex head to remove the stud.

Remove the 15mm stud

Step 6

15mm deep socket on the 2nd mounting bolt
Removal of third mounting bolt with 15mm deep socket
Here are the three bolts that hold the alternator in place. The center bolt is different since it also provides a mounting spot for the AC part.

15mm deep socket on the 2nd mounting bolt

Removal of third mounting bolt with 15mm deep socket

Here are the three bolts that hold the alternator in place. The center bolt is different since it also provides a mounting spot for the AC part.

Step 7

With the removal of the bolts the alternator can now be simply pulled out from the engine compartment
Here is the comparison with the replacement from a national parts store
New alternator in place.

With the removal of the bolts the alternator can now be simply pulled out from the engine compartment

Here is the comparison with the replacement from a national parts store

New alternator in place.

Step 8

Checked the voltage on the battery terminal with engine running. Shows properly between 14V - 15V

Checked the voltage on the battery terminal with engine running. Shows properly between 14V - 15V

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 1 other contributor

                    oldturkey03

Member since: 09/29/2010

722,353 Reputation

                                      109 Guides authored                  



                       Badges:
                       53







                                                        +50 more badges

Team

                       Global Fixers                        

                                                  Member of Global Fixers 



                    Community                     


                                            22 Members                     


                                            240 Guides authored

Member-Contributed Guide#

Introduction#

What you need#

Team#

Member-Contributed Guide

Introduction

What you need

Team