Difficulty

Easy

Steps

6

Time Required

                          15 - 25 minutes

Sections

2

  • Headlight Assembly
  • 5 steps
  • Front Turn Signal Bulb
  • 1 step

Flags

1

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • Back2002-2008 Dodge Ram

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Headlight Assembly
  • Open the hood by pulling the hood lever in the driver-side footwell.
  • Reach under the center of the grille and press the hood latch.

Open the hood by pulling the hood lever in the driver-side footwell.

Reach under the center of the grille and press the hood latch.

1024

Step 2

  • In this guide we will be removing the left headlight. The steps are mirrored for the right headlight.

In this guide we will be removing the left headlight. The steps are mirrored for the right headlight.

Step 3

  • Use the 10 mm socket wrench to unscrew the first of three 12 mm long 10 mm hex-head screws holding in the headlight assembly. The screw is located just to the left of the headlight assembly.
  • Unscrew the second screw located approximately 6 inches below the first.
  • Locate the third screw at the bottom left corner of the headlight assembly just behind the bumper and remove.
  • When re-installing the screws do not over tighten. Over tightening the screws will result in stripped threads.

Use the 10 mm socket wrench to unscrew the first of three 12 mm long 10 mm hex-head screws holding in the headlight assembly. The screw is located just to the left of the headlight assembly.

Unscrew the second screw located approximately 6 inches below the first.

Locate the third screw at the bottom left corner of the headlight assembly just behind the bumper and remove.

When re-installing the screws do not over tighten. Over tightening the screws will result in stripped threads.

Step 4

  • Approach this step with the process of unbuttoning a shirt in mind.
  • Be careful if the rubber gasket is dry-rotted. Use vaseline to re-moisturize if necessary. Manipulating dry-rotted rubber will result in tearing.
  • Pinch the bottom of the rubber gasket at the left side of the assembly and remove it from the plastic “buttons” on the headlight assembly.

Approach this step with the process of unbuttoning a shirt in mind.

Be careful if the rubber gasket is dry-rotted. Use vaseline to re-moisturize if necessary. Manipulating dry-rotted rubber will result in tearing.

Pinch the bottom of the rubber gasket at the left side of the assembly and remove it from the plastic “buttons” on the headlight assembly.

Step 5

  • Locate the blue headlight wire. Use a flathead screwdriver to pry up one side of the clamping teeth and pull the connector off.
  • Locate the green turn signal wire clamp. Use a flathead screwdriver to push in the tab on the side and pull off the connector.
  • Now that all connections between the car and the headlight assembly are disconnected, it is safe to remove the headlight assembly from the truck.

Locate the blue headlight wire. Use a flathead screwdriver to pry up one side of the clamping teeth and pull the connector off.

Locate the green turn signal wire clamp. Use a flathead screwdriver to push in the tab on the side and pull off the connector.

Now that all connections between the car and the headlight assembly are disconnected, it is safe to remove the headlight assembly from the truck.

Step 6

              Front Turn Signal Bulb
  • Turn the turn signal bulb holder counterclockwise until it stops.
  • Remove the bulb holder.
  • Inspect the bulb. Check for broken filaments or cracked glass.
  • Be sure to replace the turn signal bulb with the correct type for your Dodge. Using an incorrect bulb will result in shortened bulb or fuse lifespan.

Turn the turn signal bulb holder counterclockwise until it stops.

Remove the bulb holder.

Inspect the bulb. Check for broken filaments or cracked glass.

Be sure to replace the turn signal bulb with the correct type for your Dodge. Using an incorrect bulb will result in shortened bulb or fuse lifespan.

To reassemble the headlight assembly, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.

Author

                                      with 6 other contributors 


                    Michael Saggese

Member since: 10/05/2012

1,021 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       Cal Poly, Team 3-24, Amido Fall 2012                        

                                                  Member of Cal Poly, Team 3-24, Amido Fall 2012 



                    CPSU-AMIDO-F12S3G24                     


                                            4 Members                     


                                            11 Guides authored

Kimberly Parrish-Sanders - Nov 17, 2019

Reply

WRONG! Just reach around behind and pop the bulb out. This is A LOT of unnecessary steps for absolutely NO REASON.

Randy Drues - Aug 21, 2021

haha…try that on my 2007! Drivers side is impossible to reach. gotta take the whole light fixture.

alan burton - Feb 6, 2020

Reply

How do you change left side FRONT turn signal bulb on a 2011 CHRYSLER 200

no way you can change my CHRYSLER 2011 200 model this way