Difficulty
Moderate
Steps
9
Time Required
15 - 20 minutes
Sections
1
- Radio
- 9 steps
Flags
0
Back2005 Honda CRV
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Radio
- In the middle of the dashboard, locate the radio panel along with the shroud cover.
In the middle of the dashboard, locate the radio panel along with the shroud cover.
1024
Step 2
- Remove the two 10mm screws using a Phillips #2 screwdriver underneath the radio shroud in order to remove the radio shroud from the dashboard.
Remove the two 10mm screws using a Phillips #2 screwdriver underneath the radio shroud in order to remove the radio shroud from the dashboard.
Step 3
- Wiggle and pull the dashboard shroud until it comes free from the dashboard.
- Even when loosened, the shroud may be difficult to pull off and remove. Do not be afraid to use force to remove the panel from the dashboard.
Wiggle and pull the dashboard shroud until it comes free from the dashboard.
Even when loosened, the shroud may be difficult to pull off and remove. Do not be afraid to use force to remove the panel from the dashboard.
Step 4
- With the dashboard shroud removed, the power chord for the passenger airbag light will be clearly visible with a green connector. Push down on the disconnect tab and remove the chord from the shroud.
- Use caution when removing the passenger light cord as excessive force may cause damage.
With the dashboard shroud removed, the power chord for the passenger airbag light will be clearly visible with a green connector. Push down on the disconnect tab and remove the chord from the shroud.
Use caution when removing the passenger light cord as excessive force may cause damage.
Step 5
- With all 4 screw mounting points for the radio unit visible, unscrew each 12mm screw using a Phillips #2 screwdriver.
With all 4 screw mounting points for the radio unit visible, unscrew each 12mm screw using a Phillips #2 screwdriver.
Step 6
- With all mounting screws removed, pull out the radio unit from the dashboard, revealing 3 cables connected to the back of the unit.
With all mounting screws removed, pull out the radio unit from the dashboard, revealing 3 cables connected to the back of the unit.
Step 7
- With all cables visible, locate the antenna cable on the far right and detach it from the radio box
With all cables visible, locate the antenna cable on the far right and detach it from the radio box
Step 8
- Remove both the white steering wheel control cable and the blue power connector cable by pushing down on the removal tabs.
- Use caution to avoid excessively stressing exposed cables during removal, making sure to exert force only on the plastic removal tabs.
Remove both the white steering wheel control cable and the blue power connector cable by pushing down on the removal tabs.
Use caution to avoid excessively stressing exposed cables during removal, making sure to exert force only on the plastic removal tabs.
Step 9
- With all cables removed from the radio unit, fully remove the radio from the dashboard.
With all cables removed from the radio unit, fully remove the radio from the dashboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Matthew Sutton
Member since: 01/23/2020
219 Reputation
1 Guide authored
Badges:
8
+5 more badges
Team
Embry-Riddle Aeronautical University, Team S19-G8, Ives Spring 2020
Member of Embry-Riddle Aeronautical University, Team S19-G8, Ives Spring 2020
ERAU-IVES-S20S19G8
3 Members
1 Guide authored
Justin - Oct 13, 2021
Reply
I have to replace the 4 mounting bracket screws on my CRV, does anyone know what size/thread pitch I need?
Mike Tarsus - May 24, 2022
Check-out this website. Lots of good/useful info.
