Difficulty
Difficult
Steps
14
Time Required
5 - 7 hours
Sections
1
- Bass Speakers
- 14 steps
Flags
5
Inconsistent Images
Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.
Confusing Text
Some of this guide’s text is confusing, duplicated, or off-topic. Clarify it by editing!
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Needs More Images
A few more images would make this guide’s procedures crystal clear.
Better Introduction
Improve this guide by completing or revising its introduction.
Back2003-2007 Honda Accord
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Bass Speakers
- Using plastic opening tools, remove the floor trim panel on the driver’s side door.
Using plastic opening tools, remove the floor trim panel on the driver’s side door.
1024
Step 2
- Remove the shifter frame panel with the same opening tools.
Remove the shifter frame panel with the same opening tools.
Step 3
- Unclip the heated seats harnesses.
- Remove the 12V power supply connection.
Unclip the heated seats harnesses.
Remove the 12V power supply connection.
Step 4
- Remove the cubby space to access the head unit.
Remove the cubby space to access the head unit.
Step 5
- Remove the center climate vents with the opening tools.
Remove the center climate vents with the opening tools.
Step 6
- Remove the head unit from the dash.
Remove the head unit from the dash.
Step 7
- Attach the wiring harness into the amp by clipping it in.
Attach the wiring harness into the amp by clipping it in.
Step 8
- Run the wires under the back seat and along the driver’s side door sill (removed in step 1) to under the steering wheel.
Run the wires under the back seat and along the driver’s side door sill (removed in step 1) to under the steering wheel.
Step 9
- Find a spot to drill a hole through the firewall under steering wheel area in the footwell.
Find a spot to drill a hole through the firewall under steering wheel area in the footwell.
Step 10
- Run the power and ground wires from the trunk through the door sill and through the firewall to the engine bay.
Run the power and ground wires from the trunk through the door sill and through the firewall to the engine bay.
Step 11
- Now run the power wire where it will be out of the way.
- Run the power wire (red) and the ground wire (green) to battery, connect red to positive and green ground to a clean piece of the car body.
- Make sure to leave the power wire off until finished.
Now run the power wire where it will be out of the way.
Run the power wire (red) and the ground wire (green) to battery, connect red to positive and green ground to a clean piece of the car body.
Make sure to leave the power wire off until finished.
Step 12
- Remove the wiring harness from the back of the head unit.
- Connect the four speaker wires and one remote wire to the harness as suggested in the owner’s manual.
Remove the wiring harness from the back of the head unit.
Connect the four speaker wires and one remote wire to the harness as suggested in the owner’s manual.
Step 13
- Clamp down the wire harness on the five wires.
- Tape up the wire loom to keep it neat.
- Finally insert it back into the head unit.
Clamp down the wire harness on the five wires.
Tape up the wire loom to keep it neat.
Finally insert it back into the head unit.
Step 14
- At last put the head unit, and the panels back into the car.
At last put the head unit, and the panels back into the car.
To reassemble your device, follow the instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 1 other contributor
Frankie
Member since: 03/24/2021
253 Reputation
1 Guide authored
Badges:
7
+4 more badges
Team
UMass Dartmouth, Team S1-G2, Riel Spring 2021
Member of UMass Dartmouth, Team S1-G2, Riel Spring 2021
UMASSD-RIEL-S21S1G2
1 Member
1 Guide authored
