Difficulty

Difficult

Steps

10

Time Required

                          20 - 30 minutes

Sections

1

  • Mid-Range Door Speaker
  • 10 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

  • Back2011-2013 Scion tC

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Mid-Range Door Speaker
  • Using plastic pry tool. Pry silver cover from handle.

Using plastic pry tool. Pry silver cover from handle.

1024

Step 2

  • Using plastic pry tool. Pry Control panel off which controls locking, unlocking and windows.

Using plastic pry tool. Pry Control panel off which controls locking, unlocking and windows.

Step 3

  • Un-attach white header(connector) from control panel. Push side tab on side of white connector if a little stuck.

Un-attach white header(connector) from control panel. Push side tab on side of white connector if a little stuck.

Step 4

  • Using pry tool. Pry off plastic plate in section of door lock or pull handle.

Using pry tool. Pry off plastic plate in section of door lock or pull handle.

Step 5

  • Remove the #4 25mm screw and the #2 25mm screw on panel with a standard Phillips Screwdriver.

Remove the #4 25mm screw and the #2 25mm screw on panel with a standard Phillips Screwdriver.

Step 6

  • Pry Off Full Door Panel starting at bottom and working up the side, pulling fairly hard waiting. Clicking noises are a good sign the door panel is unlocking.

Pry Off Full Door Panel starting at bottom and working up the side, pulling fairly hard waiting. Clicking noises are a good sign the door panel is unlocking.

Step 7

  • Once door panel is free, remember to remove header from the tweeter in upper right hand corner of panel.

Once door panel is free, remember to remove header from the tweeter in upper right hand corner of panel.

Step 8

  • Remove bracket from door by unscrewing the two 14 mm nuts pictured here connected to the speaker unit.

Remove bracket from door by unscrewing the two 14 mm nuts pictured here connected to the speaker unit.

Step 9

  • Remove speaker from bracket by unscrewing the two #2 12mm screws using a Phillips head screwdriver.

Remove speaker from bracket by unscrewing the two #2 12mm screws using a Phillips head screwdriver.

Step 10

  • Desolder wires to new speaker unit using solder wick or a desoldering tool.
  • If you don’t have experience soldering, make sure to check out this soldering guide.
  • Soldering uses high temperatures. Be careful not to damage the components or injure yourself in the process.

Desolder wires to new speaker unit using solder wick or a desoldering tool.

If you don’t have experience soldering, make sure to check out this soldering guide.

Soldering uses high temperatures. Be careful not to damage the components or injure yourself in the process.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors 


                    sdwelsh

Member since: 05/04/2015

187 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       Cal Poly, Team 8-2, Regan Spring 2015                        

                                                  Member of Cal Poly, Team 8-2, Regan Spring 2015 



                    CPSU-REGAN-S15S8G2                     


                                            5 Members                     


                                            7 Guides authored

pauliemcfly25 - Oct 7, 2020

Reply

Are they 6.5 subwoofer lower door or 6×9