Difficulty

Moderate

Steps

10

Time Required

                          45 minutes

Sections

1

  • Tail Light
  • 10 steps

Flags

0

  • Back2010-2015 Hyundai Elantra

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Tail Light
  • Open the trunk.
  • Lift the latch built into the carpet liner on the right side. Remove the cover in order to see the bulb covers.
  • Be careful to not rip the carpet upon removal.

Open the trunk.

Lift the latch built into the carpet liner on the right side. Remove the cover in order to see the bulb covers.

Be careful to not rip the carpet upon removal.

1024

Step 2

  • You will then use your 10mm socket to remove three nuts, careful not to strip the screw to ensure easy replacement.

You will then use your 10mm socket to remove three nuts, careful not to strip the screw to ensure easy replacement.

Step 3

  • Once the bolts are removed, you will need to remove the wires connected to the bulb casing. Firmly push in on the center piece at the base of the wire and pull directly out to remove.

Once the bolts are removed, you will need to remove the wires connected to the bulb casing. Firmly push in on the center piece at the base of the wire and pull directly out to remove.

Step 4

  • Once the wires are disconnected facing the bumper, firmly grasp the entire plastic casing of the tail light and pull directly towards your hips in order to not catch the hidden clip located on the side of the car near the end of the tail light casing.

Once the wires are disconnected facing the bumper, firmly grasp the entire plastic casing of the tail light and pull directly towards your hips in order to not catch the hidden clip located on the side of the car near the end of the tail light casing.

Step 5

  • In order to remove the main brake/tail light, remove small light first. This is the same process for the main light. Using pliers grip the plastic and pull while rotating counterclockwise 30 degrees and remove the bulb from the socket.
  • Repeat this step to remove main bulb as well.

In order to remove the main brake/tail light, remove small light first. This is the same process for the main light. Using pliers grip the plastic and pull while rotating counterclockwise 30 degrees and remove the bulb from the socket.

Repeat this step to remove main bulb as well.

Step 6

  • Put a new Sylvania long life bulb into the socket until you hear it click.

Put a new Sylvania long life bulb into the socket until you hear it click.

Step 7

  • You can now begin the re assembly of parts. Start by re assembling the plastic cap to create a water proof seal.

You can now begin the re assembly of parts. Start by re assembling the plastic cap to create a water proof seal.

Step 8

  • After you seal the bulb, you will then place the entire casing back into the bumper ensuring that the hidden clip mentioned earlier is attached. Then, re attach the wires, you should hear a clicking sound when wire is properly placed in socket.

After you seal the bulb, you will then place the entire casing back into the bumper ensuring that the hidden clip mentioned earlier is attached. Then, re attach the wires, you should hear a clicking sound when wire is properly placed in socket.

Step 9

  • Next you will need to screw on the three bolts used previously with a 10 mm socket making sure they are tight and secure.

Next you will need to screw on the three bolts used previously with a 10 mm socket making sure they are tight and secure.

Step 10

  • Reattach the carpet liner and close the trunk.
  • Test your bulb and make sure it is running properly.

Reattach the carpet liner and close the trunk.

Test your bulb and make sure it is running properly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Wade Carter

Member since: 01/23/2019

181 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       USF Sarasota-Manatee, Team S1-G1, Stewart Spring 2019                        

                                                  Member of USF Sarasota-Manatee, Team S1-G1, Stewart Spring 2019 



                    USFSM-STEWART-S19S1G1                     


                                            18 Members                     


                                            24 Guides authored