2011 Jeep Grand Cherokee Tail Light Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 minutes

Sections

Tail Light
6 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Back2011-2014 Jeep Grand Cherokee
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Tail Light

Here is the outer tail lamp that will get replaced.
Open the liftgate to access and remove the two plastic push-pin fasteners that secure the inboard side of the lamp to the side jamb of the liftgate opening.

Here is the outer tail lamp that will get replaced.

Open the liftgate to access and remove the two plastic push-pin fasteners that secure the inboard side of the lamp to the side jamb of the liftgate opening.

1024

Step 2

Remove the push pin fastener with either a screwdriver or the appropriate tool if available.
Here is how the pin works. If the center pin is pushed in the legs expand into the hole for it. This provides the hold. To release, pull the pin.
Same with the bottom pin. Remove that.

Remove the push pin fastener with either a screwdriver or the appropriate tool if available.

Here is how the pin works. If the center pin is pushed in the legs expand into the hole for it. This provides the hold. To release, pull the pin.

Same with the bottom pin. Remove that.

Step 3

Pull the outboard side of the lamp rearward far enough to disengage the two ball studs on the back of the lamp housing from the plastic grommets in the lamp opening of the body sheet metal.
This will create a gap between the body and the lamp.
Locate and remove the plastic push-pin fastener that secures the bracket on the bottom of the inboard side of the outer rear tail lamp housing to the upper flange of the rear fascia. Use a thin tool for some gentle prying if the pins are a little hard to remove.

Pull the outboard side of the lamp rearward far enough to disengage the two ball studs on the back of the lamp housing from the plastic grommets in the lamp opening of the body sheet metal.

This will create a gap between the body and the lamp.

Locate and remove the plastic push-pin fastener that secures the bracket on the bottom of the inboard side of the outer rear tail lamp housing to the upper flange of the rear fascia. Use a thin tool for some gentle prying if the pins are a little hard to remove.

Step 4

The lamp is now off the vehicle but the wiring is still connected.
Pull the lamp away from the vehicle far enough to access and disconnect the two body wire harness connectors
The smaller bottom connector (here right) is the back-up lamp and the larger one is the bulb for tail/stop/rear side marker/turn signal function. Grasp the bulb socket on the back of the rear lamp unit rotate it counterclockwise about 30 degrees to unlock it. Pull the socket and bulb straight out from the keyed opening in the housing.

The lamp is now off the vehicle but the wiring is still connected.

Pull the lamp away from the vehicle far enough to access and disconnect the two body wire harness connectors

The smaller bottom connector (here right) is the back-up lamp and the larger one is the bulb for tail/stop/rear side marker/turn signal function. Grasp the bulb socket on the back of the rear lamp unit rotate it counterclockwise about 30 degrees to unlock it. Pull the socket and bulb straight out from the keyed opening in the housing.

Step 5

Here is the new aftermarket lens
Insert the bulb socket into the new lens opening lining up the notches from the socket and the lens.
Rotate the complete bulb socket about 30 degrees in a clockwise direction.

Here is the new aftermarket lens

Insert the bulb socket into the new lens opening lining up the notches from the socket and the lens.

Rotate the complete bulb socket about 30 degrees in a clockwise direction.

Step 6

New backlight installed and passed inspection.

New backlight installed and passed inspection.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    oldturkey03

Member since: 09/29/2010

722,365 Reputation

                                      109 Guides authored                  



                       Badges:
                       53







                                                        +50 more badges

Team

                       Global Fixers                        

                                                  Member of Global Fixers 



                    Community                     


                                            22 Members                     


                                            240 Guides authored

Member-Contributed Guide#

Introduction#

What you need#

Team#

Member-Contributed Guide

Introduction

What you need

Team