Difficulty
Moderate
Steps
10
Time Required
8 minutes
Sections
2
- Battery
- 6 steps
- SD Card
- 4 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
Back360fly 4K
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Flip the camera upside down and peel off the two plastic screw covers with the metal spudger to reveal the screws.
Flip the camera upside down and peel off the two plastic screw covers with the metal spudger to reveal the screws.
1024
Step 2
- Remove the two 5 mm screws from the bottom of the camera with a T4 screwdriver.
Remove the two 5 mm screws from the bottom of the camera with a T4 screwdriver.
Step 3
- Gently pry the plastic ring from around the charging plate with the metal spudger.
- Remove the outside shell by pressing against the center of the charging plate and pulling the bottom shell away from the top shell.
Gently pry the plastic ring from around the charging plate with the metal spudger.
Remove the outside shell by pressing against the center of the charging plate and pulling the bottom shell away from the top shell.
Step 4
- Remove the five 2 mm screws using a T4 screwdriver.
- Pull off the charging plate assembly.
Remove the five 2 mm screws using a T4 screwdriver.
Pull off the charging plate assembly.
Step 5
- Gently pry the plug off the port on the circuit board with a plastic opening tool.
- Remove the four 2 mm screws using a T4 screwdriver.
- Remove the circuit board from the device.
Gently pry the plug off the port on the circuit board with a plastic opening tool.
Remove the four 2 mm screws using a T4 screwdriver.
Remove the circuit board from the device.
Step 6
- Remove the five 4 mm screws around the battery assembly with a T4 screwdriver.
- Lift the battery assembly and gently pry the plug out of its port on the board below with a plastic opening tool.
- Press the battery from the back of the battery assembly to remove it with a plastic opening tool until the glue releases the battery.
- Potential for device damage: Do not puncture or bend the battery. Use a small amount of heat to assist in softening the adhesive if necessary.
Remove the five 4 mm screws around the battery assembly with a T4 screwdriver.
Lift the battery assembly and gently pry the plug out of its port on the board below with a plastic opening tool.
Press the battery from the back of the battery assembly to remove it with a plastic opening tool until the glue releases the battery.
Potential for device damage: Do not puncture or bend the battery. Use a small amount of heat to assist in softening the adhesive if necessary.
Step 7
SD Card
- Gently pry the plug from the motherboard and remove the motherboard from the assembly.
Gently pry the plug from the motherboard and remove the motherboard from the assembly.
Step 8
- Remove the three 3 mm screws from the circuit assembly with a T4 screwdriver.
Remove the three 3 mm screws from the circuit assembly with a T4 screwdriver.
Step 9
- Gently pry out the plug from the circuit assembly.
Gently pry out the plug from the circuit assembly.
Step 10
- Press and release the SD card to remove it from the circuit assembly.
Press and release the SD card to remove it from the circuit assembly.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 3 other contributors
Jacob Herron
Member since: 11/08/2017
463 Reputation
3 Guides authored
Badges:
8
+5 more badges
Team
IUPUI, Team S5-G3, Baechle Fall 2017
Member of IUPUI, Team S5-G3, Baechle Fall 2017
IUPUI-BAECHLE-F17S5G3
3 Members
3 Guides authored
John Erikson - Mar 21, 2018
Reply
Really useful guide, thanks
