Difficulty

Moderate

Steps

10

Time Required

                          5 minutes

Sections

2

  • Propeller
  • 3 steps
  • Leg
  • 7 steps

Flags

0

  • Back3DR Solo

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Propeller
  • Grip the arm, which is located underneath the propeller, with one hand, and with your dominant hand grip the center of the propeller.

Grip the arm, which is located underneath the propeller, with one hand, and with your dominant hand grip the center of the propeller.

1024

Step 2

  • Twist the propeller from the locked to unlocked position as indicated by the images of the lock.
  • You will need to twist in this direction for 2-3 full rotations before the propeller will detach.

Twist the propeller from the locked to unlocked position as indicated by the images of the lock.

You will need to twist in this direction for 2-3 full rotations before the propeller will detach.

Step 3

  • Lift the propeller off the motor.
  • To remove the silver-top propellers, repeat these steps, turning the propellers in the opposite direction of the black-top propellers.

Lift the propeller off the motor.

To remove the silver-top propellers, repeat these steps, turning the propellers in the opposite direction of the black-top propellers.

Step 4

              Leg
  • Place the controller on a flat surface with the battery side down.

Place the controller on a flat surface with the battery side down.

Step 5

  • Locate the leg and remove the two 10mm screws that hold the leg in place.

Locate the leg and remove the two 10mm screws that hold the leg in place.

Step 6

  • Gently pull the leg up to remove it from its position.
  • Leg should be connected by a black wire.

Gently pull the leg up to remove it from its position.

Leg should be connected by a black wire.

Step 7

  • Locate the rubber grip at the end of the leg and, with your thumb, peel it back and pull it off.

Locate the rubber grip at the end of the leg and, with your thumb, peel it back and pull it off.

Step 8

  • Leg type 1 will contain a 1mm screw at the base of the leg.
  • Unscrew the 1mm screw located at the end of the leg.

Leg type 1 will contain a 1mm screw at the base of the leg.

Unscrew the 1mm screw located at the end of the leg.

Step 9

  • Gently pull the black cord up to release it from the leg.

Gently pull the black cord up to release it from the leg.

Step 10

  • Leg type 2 will contain the antenna wire.
  • Gently pull up on and remove the plastic covering labeled “solo antenna”.
  • Locate the antenna wire and carefully pull up and remove it.
  • The antenna wire is flimsy so use caution upon removal.

Leg type 2 will contain the antenna wire.

Gently pull up on and remove the plastic covering labeled “solo antenna”.

Locate the antenna wire and carefully pull up and remove it.

The antenna wire is flimsy so use caution upon removal.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Leia Harlow

Member since: 09/11/2017

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       CSU Fullerton, Team S2-G3, Bruce Fall 2017                        

                                                  Member of CSU Fullerton, Team S2-G3, Bruce Fall 2017 



                    CSUF-BRUCE-F17S2G3                     


                                            4 Members                     


                                            5 Guides authored