Difficulty

Moderate

Steps

12

Time Required

                          30 - 35 minutes

Sections

3

  • Back Cover
  • 5 steps
  • Motherboard
  • 6 steps
  • Screen
  • 1 step

Flags

1

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

  • BackAarp RealPad MA7BX2

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Loosen the back cover using the suction cup.
  • Pull up on the center of the back with the suction cup.
  • Pull up on all four corners of the back with the suction cup.

Loosen the back cover using the suction cup.

Pull up on the center of the back with the suction cup.

Pull up on all four corners of the back with the suction cup.

1024

Step 2

  • Remove the back cover by gently placing the small opening tool in the crevice created by loosening the back.
  • Slide the opening tool around the edges of the device.
  • Wedge it open using the opening tool.
  • Use the suction cup again if you’re having trouble removing the back cover.

Remove the back cover by gently placing the small opening tool in the crevice created by loosening the back.

Slide the opening tool around the edges of the device.

Wedge it open using the opening tool.

Use the suction cup again if you’re having trouble removing the back cover.

Step 3

  • The black tape is stuck to delicate wires; remove with caution.
  • Peel off the silver tape.
  • Gently pull off the black tape.

The black tape is stuck to delicate wires; remove with caution.

Peel off the silver tape.

Gently pull off the black tape.

Step 4

  • Using a JIS #000 screwdriver, remove the two 2.5 mm screws.

Using a JIS #000 screwdriver, remove the two 2.5 mm screws.

Step 5

  • Lift off the black audio cover.

Lift off the black audio cover.

Step 6

              Motherboard
  • Remove the two JIS #000 screws.

Remove the two JIS #000 screws.

Step 7

  • Flip up the small black connectors using a spudger or your nails.
  • Be careful when flipping them up. Too much force can cause them to break.

Flip up the small black connectors using a spudger or your nails.

Be careful when flipping them up. Too much force can cause them to break.

Step 8

  • Remove battery.
  • Removing the battery may need some force. Be careful as to not break anything.

Remove battery.

Removing the battery may need some force. Be careful as to not break anything.

Step 9

  • Use the tweezers to loosen up the sides of speakers by going into the gaps, before picking it up.
  • There are magnets holding down the speakers. Be careful as to not pick them up with the speakers.
  • The top of the speakers are very fragile and may fall out at the slightest touch. Be careful when picking them up.

Use the tweezers to loosen up the sides of speakers by going into the gaps, before picking it up.

There are magnets holding down the speakers. Be careful as to not pick them up with the speakers.

The top of the speakers are very fragile and may fall out at the slightest touch. Be careful when picking them up.

Step 10

  • Remove all wire connections by sliding them out of the connectors.
  • Be careful as to not forcefully pull out anything because the wires are very delicate.

Remove all wire connections by sliding them out of the connectors.

Be careful as to not forcefully pull out anything because the wires are very delicate.

Step 11

  • Take off the motherboard and set it aside. Your Finished product should look like this.

Take off the motherboard and set it aside. Your Finished product should look like this.

Step 12

              Screen
  • Use the suction cup to loosen and pull up the screen.
  • Be careful when pulling up screen. Too much force can lead to you breaking it.

Use the suction cup to loosen and pull up the screen.

Be careful when pulling up screen. Too much force can lead to you breaking it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Alana Escue

Member since: 09/18/2018

425 Reputation

                                      3 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       University of North Texas, Team S4-G7, Raign Fall 2018                        

                                                  Member of University of North Texas, Team S4-G7, Raign Fall 2018 



                    UNT-RAIGN-F18S4G7                     


                                            5 Members                     


                                            4 Guides authored

Jackson Reynolds - Nov 27, 2018

Reply

Remember to give the lengths for all screws. For warnings, try to be more straight forward and try not to use words like ‘“note.” Remember to add an introduction.