Difficulty
Moderate
Steps
10
Time Required
15 - 30 minutes
Sections
2
- Removing Samsung ML2510 Back Panel
- 3 steps
- Accessing Samsung ML2510 Circuit Board
- 7 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackSamsung ML-2510
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Removing Samsung ML2510 Back Panel
- Remove the top hinged panel by taking out the pins at the bottom of this panel.
Remove the top hinged panel by taking out the pins at the bottom of this panel.
1024
Step 2
- Using a Phillips #2 screwdriver, remove the four screws on the back of the printer.
Using a Phillips #2 screwdriver, remove the four screws on the back of the printer.
Step 3
- Gently lift the top panel while simultaneously pulling off the back panel.
- Before pulling out the back panel entirely, make sure to remove the rear cooling fan from its slot.
Gently lift the top panel while simultaneously pulling off the back panel.
Before pulling out the back panel entirely, make sure to remove the rear cooling fan from its slot.
Step 4
Accessing Samsung ML2510 Circuit Board
- Remove the front panel by gently freeing the holes on the panel from the pegs attached to the main printer body one at a time. Make sure to remove the entire front panel, not just the flap on the paper tray.
Remove the front panel by gently freeing the holes on the panel from the pegs attached to the main printer body one at a time. Make sure to remove the entire front panel, not just the flap on the paper tray.
Step 5
- Using a Phillips #2 screwdriver, remove the two 1" screws on the front face of the printer.
Using a Phillips #2 screwdriver, remove the two 1" screws on the front face of the printer.
Step 6
- Using a plastic opening tool, gently lift one side of the top panel from its peg.
- Repeat the process for the other side.
- Lift the top panel from the front to remove it entirely.
Using a plastic opening tool, gently lift one side of the top panel from its peg.
Repeat the process for the other side.
Lift the top panel from the front to remove it entirely.
Step 7
- Lift the right panel up from the raised stops.
- Rotate the panel gently as indicated in the picture to remove the panel entirely.
Lift the right panel up from the raised stops.
Rotate the panel gently as indicated in the picture to remove the panel entirely.
Step 8
- Using a Phillips #2 screwdriver, remove the four 1" screws attaching the gray plate to the printer.
- Remove the plastic cover by sliding it carefully under the silver hinges on the right.
Using a Phillips #2 screwdriver, remove the four 1" screws attaching the gray plate to the printer.
Remove the plastic cover by sliding it carefully under the silver hinges on the right.
Step 9
- Using a Phillips #2 screwdriver, remove the 1" screw attaching the circuit board to the printer.
Using a Phillips #2 screwdriver, remove the 1" screw attaching the circuit board to the printer.
Step 10
- Turn over the circuit board to access main wiring.
- Unplug the wiring from the circuit board gently.
Turn over the circuit board to access main wiring.
Unplug the wiring from the circuit board gently.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
Author
with 9 other contributors
bbaustin
Member since: 10/12/2011
247 Reputation
6 Guides authored
Badges:
11
+8 more badges
Team
Cal Poly, Team 17-18, Regan Fall 2011
Member of Cal Poly, Team 17-18, Regan Fall 2011
CPSU-REGAN-F11S17G18
4 Members
6 Guides authored
