Acer Al1714 Power Button Circuit Board Repair Guide

Difficulty

Moderate

Steps

Time Required

Suggest a time??

Sections

Power Button Circuit Board
16 steps

Flags

BackAcer AL1714
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Power Button Circuit Board

Turn the monitor facedown.
Unscrew the 5 screws holding the back cover on.
(This may require flipping the monitor over and shaking the screws loose once they’re already unscrewed)

Turn the monitor facedown.

Unscrew the 5 screws holding the back cover on.

(This may require flipping the monitor over and shaking the screws loose once they’re already unscrewed)

1024

Step 2

Take the edge tool or a metal ruler and insert it into the bezel.
Apply pressure and push down.
Do the same to the right side.
Once the side of bezel facing you is decoupled, take the back cover and pry it loose.

Take the edge tool or a metal ruler and insert it into the bezel.

Apply pressure and push down.

Do the same to the right side.

Once the side of bezel facing you is decoupled, take the back cover and pry it loose.

Step 3

Remove the Flat Flex Cable from the Power Supply Board under the metal cover.
Pull the cord back and out of the way.
(It may be stuck down with adhesive)

Remove the Flat Flex Cable from the Power Supply Board under the metal cover.

Pull the cord back and out of the way.

(It may be stuck down with adhesive)

Step 4

Unscrew the cord anchors for the VGA port.
(Use needle nose pliers if they’re too tight for removal by hand)

Unscrew the cord anchors for the VGA port.

(Use needle nose pliers if they’re too tight for removal by hand)

Step 5

Turn the monitor around.
Unscrew the 1 screw holding the Flex Power Cable cover.
Lift up and remove the Flex Power Cable cover.
(Careful: This may be sharp)

Turn the monitor around.

Unscrew the 1 screw holding the Flex Power Cable cover.

Lift up and remove the Flex Power Cable cover.

(Careful: This may be sharp)

Step 6

Unscrew the 5 screws holding the metal cage on.

Unscrew the 5 screws holding the metal cage on.

Step 7

Turn the monitor around.
Lift up on the back of the metal cage slightly.
Pull the cage toward self.
(Must be careful to free the cover of the VGA port and power supply input)

Lift up on the back of the metal cage slightly.

Pull the cage toward self.

(Must be careful to free the cover of the VGA port and power supply input)

Step 8

Lift up on the Flat Flex Cable holder tabs to release cords.
Lift up on the Flat Flex Cables and bend them out of the working area.

Lift up on the Flat Flex Cable holder tabs to release cords.

Lift up on the Flat Flex Cables and bend them out of the working area.

Step 9

Unplug the 4 backlight wires from their ports on the Power Supply Board.
(Considering their size, the best way to unplug the backlight wires is by slowly jiggling wires out of place)

Unplug the 4 backlight wires from their ports on the Power Supply Board.

(Considering their size, the best way to unplug the backlight wires is by slowly jiggling wires out of place)

Step 10

Unscrew the 5 screws holding the Power Supply Board and Video Display boards on.

Unscrew the 5 screws holding the Power Supply Board and Video Display boards on.

Step 11

Lift up and remove the joined Power Supply Board and Video Display boards.

Lift up and remove the joined Power Supply Board and Video Display boards.

Step 12

Carefully detach the Power Supply and Video Display boards at their connector joint.
(This step is not necessary for the removal and replacement of the Power Button Circuit board)
(This is only a precaution so as not to bend or break the connector joint between the two boards)

Carefully detach the Power Supply and Video Display boards at their connector joint.

(This step is not necessary for the removal and replacement of the Power Button Circuit board)

(This is only a precaution so as not to bend or break the connector joint between the two boards)

Step 13

Remove the Flat Flex Cable from the Power Button Circuit Board.

Remove the Flat Flex Cable from the Power Button Circuit Board.

Step 14

Grasp, lift, and remove the LCD Module from the front panel.

Grasp, lift, and remove the LCD Module from the front panel.

Step 15

Unscrew the 2 screws holding the Power Button Circuit Board.

Unscrew the 2 screws holding the Power Button Circuit Board.

Step 16

Lift and remove the Power Button Circuit Board.

Lift and remove the Power Button Circuit Board.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 4 other contributors

                    Hussam Alzamzami

Member since: 09/25/2014

216 Reputation

                                      1 Guide authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team 1-3, Brown Fall 2014                        

                                                  Member of USF Tampa, Team 1-3, Brown Fall 2014 



                    USFT-BROWN-F14S1G3                     


                                            3 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team