Difficulty

Easy

Steps

9

Time Required

                          15 minutes

Sections

3

  • Stand
  • 3 steps
  • Outer Case
  • 3 steps
  • EMI Shield
  • 3 steps

Flags

0

  • BackAcer AL1916

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Stand
  • Lay the monitor on a flat surface so that the back is facing up.

Lay the monitor on a flat surface so that the back is facing up.

1024

Step 2

  • Grab the hinge cover with both hands on either side of the stand.
  • Squeeze inwards with your thumbs and fingers and lift up to remove the hinge cover.

Grab the hinge cover with both hands on either side of the stand.

Squeeze inwards with your thumbs and fingers and lift up to remove the hinge cover.

Step 3

  • Remove the four 12.1 mm Phillips #2 screws that hold the stand to the monitor.
  • Support the monitor while removing the screws to prevent the monitor from falling.
  • Lift up to detach the stand.

Remove the four 12.1 mm Phillips #2 screws that hold the stand to the monitor.

Support the monitor while removing the screws to prevent the monitor from falling.

Lift up to detach the stand.

Step 4

              Outer Case
  • Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor.

Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor.

Step 5

  • Starting at the corner of the monitor, wedge the small plastic opening tool between the back cover and the display bezel.
  • Tilt the plastic opening tool up to separate the back cover from the display bezel.
  • Continue around the perimeter of the monitor until the display bezel comes off.
  • A reasonable amount of force is necessary to detach the back cover from the display bezel.

Starting at the corner of the monitor, wedge the small plastic opening tool between the back cover and the display bezel.

Tilt the plastic opening tool up to separate the back cover from the display bezel.

Continue around the perimeter of the monitor until the display bezel comes off.

A reasonable amount of force is necessary to detach the back cover from the display bezel.

Step 6

  • Reposition the monitor so that the back is facing up.
  • Grab the corners of the monitor and jiggle them upwards to detach the back cover from the inside of the monitor.
  • Lift the back cover up.

Reposition the monitor so that the back is facing up.

Grab the corners of the monitor and jiggle them upwards to detach the back cover from the inside of the monitor.

Lift the back cover up.

Step 7

              EMI Shield
  • Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield.

Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield.

Step 8

  • Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input.

Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input.

Step 9

  • Grab the metal casing by the sides and slide it down towards the bottom of the monitor.
  • Lift up to remove the metal casing.
  • Beware, metal casing is sharp!

Grab the metal casing by the sides and slide it down towards the bottom of the monitor.

Lift up to remove the metal casing.

Beware, metal casing is sharp!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Taylor Atterbury

Member since: 10/06/2011

672 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 20-26, Maness Fall 2011                        

                                                  Member of Cal Poly, Team 20-26, Maness Fall 2011 



                    CPSU-MANESS-F11S20G26                     


                                            4 Members                     


                                            7 Guides authored