Acer Aspire E1 470P 6659 Cooling Fan Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          40 minutes - 1 hour

Sections

Battery
4 steps
Hard Drive
6 steps
Motherboard
2 steps
Cooling Fan
2 steps

Flags

BackAcer Aspire E1-470
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Turn off the laptop and disconnect all device cords.

Turn off the laptop and disconnect all device cords.

1024

Step 2

Flip the laptop over so the bottom is facing you.

Flip the laptop over so the bottom is facing you.

Step 3

Use your finger or a spuger to pull the battery release switch.

Use your finger or a spuger to pull the battery release switch.

Step 4

Remove the battery from the laptop.

Remove the battery from the laptop.

Step 5

              Hard Drive

Remove nineteen screws from the back panel using a Phillips #0 Screwdriver .

Remove nineteen screws from the back panel using a Phillips #0 Screwdriver .

Step 6

Run the plastic opening tool across from one corner to another along the edge.
Separate the keyboard panel gently.
Lift the keyboard slowly from the laptop but do not lift completely because there are ribbon cables attached.

Run the plastic opening tool across from one corner to another along the edge.

Separate the keyboard panel gently.

Lift the keyboard slowly from the laptop but do not lift completely because there are ribbon cables attached.

Step 7

Disconnect the two keyboard assembly ribbon cables from motherboard.
To release small ribbon cable, use spudger or fingers to flip gray bar along edge over.
To release larger ribbon cable, use pry tool or spudger to slide white plastic clip forward.

Disconnect the two keyboard assembly ribbon cables from motherboard.

To release small ribbon cable, use spudger or fingers to flip gray bar along edge over.

To release larger ribbon cable, use pry tool or spudger to slide white plastic clip forward.

Step 8

Pull up the release tab beside the hard drive.
Disconnect portion of ribbon cable that is covering the hard drive.
Handle the ribbon carefully. Do not break the metal contact.
While reconnecting the ribbon after replacing a new hard drive, face the blue side with a label up. Make sure the black line beside the sticker is not crooked, so that the ribbon is tight.

Pull up the release tab beside the hard drive.

Disconnect portion of ribbon cable that is covering the hard drive.

Handle the ribbon carefully. Do not break the metal contact.

While reconnecting the ribbon after replacing a new hard drive, face the blue side with a label up. Make sure the black line beside the sticker is not crooked, so that the ribbon is tight.

Step 9

Remove the hard drive screw using Phillips #0 Screwdriver.

Remove the hard drive screw using Phillips #0 Screwdriver.

Step 10

Pull the hard drive out gently. Be aware that it is connected to the adapter.
Gently remove adapter by pulling on both ends simultaneously to separate it from the hard drive.

Pull the hard drive out gently. Be aware that it is connected to the adapter.

Gently remove adapter by pulling on both ends simultaneously to separate it from the hard drive.

Step 11

              Motherboard

Remove additional screws that can be found on the motherboard.
Remove the green wifi card from motherboard.
Use spudger to disconnect the fan and motherboard from laptop.

Remove additional screws that can be found on the motherboard.

Remove the green wifi card from motherboard.

Use spudger to disconnect the fan and motherboard from laptop.

Step 12

Remove the cable attached to motherboard.
Gently lift and remove the motherboard from the laptop.

Remove the cable attached to motherboard.

Gently lift and remove the motherboard from the laptop.

Step 13

              Cooling Fan

Flip the motherboard and fan piece over.
Remove the four screws using the Phillips #000 Screwdriver.

Flip the motherboard and fan piece over.

Remove the four screws using the Phillips #000 Screwdriver.

Step 14

Flip the motherboard over and slowly remove the tape holding the cooling fan down.
Use a spudger to remove the top of the fan from the base of the fan.
Remove the cooling fan component from both the tape and the motherboard.

Flip the motherboard over and slowly remove the tape holding the cooling fan down.

Use a spudger to remove the top of the fan from the base of the fan.

Remove the cooling fan component from both the tape and the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Faith Lobaton

Member since: 10/22/2018

452 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UC Davis, Team S4-G5, Lore Fall 2018                        

                                                  Member of UC Davis, Team S4-G5, Lore Fall 2018 



                    UCD-LORE-F18S4G5                     


                                            3 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team