Difficulty
Moderate
Steps
15
Time Required
10 minutes
Sections
3
- Battery
- 2 steps
- Hard Drive
- 5 steps
- Keyboard
- 8 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackAcer Aspire E1-510P-4637
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery
- To release the battery, depress the battery release with a nylon spudger. Hold the latch down and slide it over.
To release the battery, depress the battery release with a nylon spudger. Hold the latch down and slide it over.
1024
Step 2
- Firmly grab hold of the battery and slide it out of the laptop.
Firmly grab hold of the battery and slide it out of the laptop.
Step 3
Hard Drive
- Remove the M2.5x8 screw with a PH1 screwdriver.
Remove the M2.5x8 screw with a PH1 screwdriver.
Step 4
- Use the plastic opening tool to pop off the small back cover.
Use the plastic opening tool to pop off the small back cover.
Step 5
- Use a PH0 Phillips screwdriver to remove the screw securing the hard drive.
Use a PH0 Phillips screwdriver to remove the screw securing the hard drive.
Step 6
- Use a nylon spudger to slightly pry up the hard drive near the screw holes.
Use a nylon spudger to slightly pry up the hard drive near the screw holes.
Step 7
- Grab hold of the plastic tab and pull the hard drive away from the connectors. This will release the hard drive.
- The hard drive connector is fragile. Handle with care.
Grab hold of the plastic tab and pull the hard drive away from the connectors. This will release the hard drive.
The hard drive connector is fragile. Handle with care.
Step 8
Keyboard
- Remove the fourteen M2.5x8 screws highlighted in the picture with a PH0 Phillips screwdriver.
Remove the fourteen M2.5x8 screws highlighted in the picture with a PH0 Phillips screwdriver.
Step 9
- Slide out the disk drive tray.
Slide out the disk drive tray.
Step 10
- Use the plastic opening tool to gently pry open the laptop.
Use the plastic opening tool to gently pry open the laptop.
Step 11
- Rotate the back cover up a little to reveal the cables connected to the motherboard.
- Unplug the cables by sliding them out of their receptacle.
- The connectors are very small and fragile. Handle with care.
Rotate the back cover up a little to reveal the cables connected to the motherboard.
Unplug the cables by sliding them out of their receptacle.
The connectors are very small and fragile. Handle with care.
Step 12
- Remove the four center panel M1.6x3 screws with a PH0 Phillips screwdriver.
- Remove the two M2x3 screws with a PH0 Phillips screwdriver.
Remove the four center panel M1.6x3 screws with a PH0 Phillips screwdriver.
Remove the two M2x3 screws with a PH0 Phillips screwdriver.
Step 13
- Use the plastic opening tool to slide the metal part out to release it from the retaining tabs.
Use the plastic opening tool to slide the metal part out to release it from the retaining tabs.
Step 14
- Peel off the foil adhesive stuck to the keyboard.
Peel off the foil adhesive stuck to the keyboard.
Step 15
- Remove the keyboard.
Remove the keyboard.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Caleb lindsay
Member since: 04/11/2016
778 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 34-15, Maness Spring 2016
Member of Cal Poly, Team 34-15, Maness Spring 2016
CPSU-MANESS-S16S34G15
4 Members
6 Guides authored
