Acer Aspire E1 531 2438 Screen Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 - 30 minutes

Sections

Battery
2 steps
Hard Drive
3 steps
Screen
9 steps

Flags

BackAcer Aspire E1-531-2438
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Unplug and power down the device before removing the battery.
Turn the device over so the back side is facing up.
Using a spudger, slide the orange latch to the right. This will release the battery, which should pop up from the device.
Use two hands tilt the side of the battery closest to the orange latch upward as shown in the images.

Unplug and power down the device before removing the battery.

Turn the device over so the back side is facing up.

Using a spudger, slide the orange latch to the right. This will release the battery, which should pop up from the device.

Use two hands tilt the side of the battery closest to the orange latch upward as shown in the images.

1024

Step 2

Tilt the side of the battery closest to the orange latch upward.
Lift the battery up and out of the device.

Tilt the side of the battery closest to the orange latch upward.

Lift the battery up and out of the device.

Step 3

              Hard Drive

Using a Phillips #0 screwdriver, remove the two 9mm screws on the access panel.

Using a Phillips #0 screwdriver, remove the two 9mm screws on the access panel.

Step 4

Using the indentation, pry open the access panel with your fingers or a spudger.
Remove the access panel to expose the hard drive, WiFi chip, and RAM modules.

Using the indentation, pry open the access panel with your fingers or a spudger.

Remove the access panel to expose the hard drive, WiFi chip, and RAM modules.

Step 5

Grip the plastic tab on the hard drive, then pull to the left to unplug the drive from its socket.
Once free from the socket, lift the hard drive up and out of the device.

Grip the plastic tab on the hard drive, then pull to the left to unplug the drive from its socket.

Once free from the socket, lift the hard drive up and out of the device.

Step 6

              Screen

Using a Phillips #0 screwdriver, remove all of the following screws:
Fifteen 9mm screws
One 6mm screw
Three 3.5mm screws

Using a Phillips #0 screwdriver, remove all of the following screws:

Fifteen 9mm screws

One 6mm screw

Three 3.5mm screws

Step 7

Remove the optical drive by sliding it out of its slot on the side of the laptop.

Remove the optical drive by sliding it out of its slot on the side of the laptop.

Step 8

Using a plastic opening tool, pry along the seam running the perimeter of the laptop to separate the bottom case from the palmrest assembly.
Flip the device over and open the laptop so that the keyboard is visible.
Lift up the palmrest assembly just far enough to access the connectors underneath.

Using a plastic opening tool, pry along the seam running the perimeter of the laptop to separate the bottom case from the palmrest assembly.

Flip the device over and open the laptop so that the keyboard is visible.

Lift up the palmrest assembly just far enough to access the connectors underneath.

Step 9

Using a pair of tweezers, disconnect the small white ribbon cable from the connector near the left side of the device.
Disconnect the large black ribbon cable near the middle of the device. Gently pull on the cable away from you.

Using a pair of tweezers, disconnect the small white ribbon cable from the connector near the left side of the device.

Disconnect the large black ribbon cable near the middle of the device. Gently pull on the cable away from you.

Step 10

Lift and remove the palmrest assembly and the attached keyboard.

Lift and remove the palmrest assembly and the attached keyboard.

Step 11

Using two hands, push toward the screen to disconnect the screen connector.

Using two hands, push toward the screen to disconnect the screen connector.

Step 12

Using a spudger, remove the circular plastic screw cover on the screws on the lower left and right of the screen.
Using a Phillips #0 screwdriver, remove the two 3mm screws hidden under the circular plastic screw covers.

Using a spudger, remove the circular plastic screw cover on the screws on the lower left and right of the screen.

Using a Phillips #0 screwdriver, remove the two 3mm screws hidden under the circular plastic screw covers.

Step 13

Using a plastic opening tool, go around the edge of the display to remove the plastic bezel.

Using a plastic opening tool, go around the edge of the display to remove the plastic bezel.

Step 14

Using a Phillips #0 screwdriver, remove the three screws in the mounting bracket along the right edge of the screen.
Remove the three screws in the mounting bracket along the left edge of the screen in the same manner.
Lift the screen out of the device.

Using a Phillips #0 screwdriver, remove the three screws in the mounting bracket along the right edge of the screen.

Remove the three screws in the mounting bracket along the left edge of the screen in the same manner.

Lift the screen out of the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Jakob Rinkus

Member since: 03/21/2019

947 Reputation

                                      7 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UMass Dartmouth, Team S8-G2, Bailey Spring 2019                        

                                                  Member of UMass Dartmouth, Team S8-G2, Bailey Spring 2019 



                    UMASSD-BAILEY-S19S8G2                     


                                            3 Members                     


                                            7 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team