Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
2
- Battery
- 2 steps
- Back Panel
- 9 steps
Flags
0
BackACER Aspire E1-572
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Before you begin, be sure to turn off your laptop and unplug it from the outlet.
- Flip your laptop over so the back panel is facing upwards.
- Locate the lock switch below the battery.
Before you begin, be sure to turn off your laptop and unplug it from the outlet.
Flip your laptop over so the back panel is facing upwards.
Locate the lock switch below the battery.
1024
Step 2
- Slide the lock switch to the right using your finger or a spudger.
- At the same time, grasp the battery with your other hand and slide it out of the laptop.
- Remove the battery.
- To reinsert or replace the battery, simply line up the tabs on the battery with the laptop and slide it straight back in. There is no need to move the lock switch.
Slide the lock switch to the right using your finger or a spudger.
At the same time, grasp the battery with your other hand and slide it out of the laptop.
Remove the battery.
To reinsert or replace the battery, simply line up the tabs on the battery with the laptop and slide it straight back in. There is no need to move the lock switch.
Step 3
Back Panel
- Remove the 16 2.5 x 8mm Phillips #0 screws from the back panel.
Remove the 16 2.5 x 8mm Phillips #0 screws from the back panel.
Step 4
- Remove the back panel by carefully disengaging it around the edges and then pull upwards.
Remove the back panel by carefully disengaging it around the edges and then pull upwards.
Step 5
- Unscrew the two remaining 2.5 x 8mm Phillips #0 screws from inside the bottom panel as designated in the image.
Unscrew the two remaining 2.5 x 8mm Phillips #0 screws from inside the bottom panel as designated in the image.
Step 6
- Slide out the plastic insert located on the left side, and remove, before returning the laptop to the face-up position.
Slide out the plastic insert located on the left side, and remove, before returning the laptop to the face-up position.
Step 7
- Carefully flip your laptop back over and open it up.
Carefully flip your laptop back over and open it up.
Step 8
- Carefully detach the top panel of the laptop and slowly lift it up to reveal the internal components.
Carefully detach the top panel of the laptop and slowly lift it up to reveal the internal components.
Step 9
- Locate the three ribbons that need to be unplugged, so the two halves of the device may be separated.
- Unplug the large ribbon by sliding the retainer clip backward (toward the hinges), then gently pulling the cable out of the connector.
Locate the three ribbons that need to be unplugged, so the two halves of the device may be separated.
Unplug the large ribbon by sliding the retainer clip backward (toward the hinges), then gently pulling the cable out of the connector.
Step 10
- Remove the other two smaller ribbons by flipping open the small plastic tab that holds the ribbon in the connector.
- Then simply pull the free ribbon out.
Remove the other two smaller ribbons by flipping open the small plastic tab that holds the ribbon in the connector.
Then simply pull the free ribbon out.
Step 11
- Lift the top panel all the way up and your laptop is now split into its two distinct halves.
Lift the top panel all the way up and your laptop is now split into its two distinct halves.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Cody Lim
Member since: 01/25/2017
1,377 Reputation
7 Guides authored
Badges:
13
+10 more badges
Team
Cal Poly, Team 9-6, Banghart Winter 2017
Member of Cal Poly, Team 9-6, Banghart Winter 2017
CPSU-BANGHART-W17S9G6
3 Members
7 Guides authored
cristianomrodrigues - Feb 6, 2020
Reply
Muito bem explicado!
