Difficulty
Moderate
Steps
9
Time Required
40 minutes - 1 hour
Sections
3
- Battery
- 3 steps
- Keyboard
- 2 steps
- CPU Fan
- 4 steps
Flags
0
BackAcer Aspire E5-571P-55TL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
This guide will explain how to replace the CPU fan for the Acer E5-571P-55TL. Before performing actions in this guide be sure to power off your laptop and remove the power adapter.
What you need
Step 1
Battery
- Make sure that laptop is turned off.
- Turn the laptop upside down with the battery facing you.
Make sure that laptop is turned off.
Turn the laptop upside down with the battery facing you.
1024
Step 2
- Place the Spudger into the battery lock and slide it to the left until you hear the battery unlock.
Place the Spudger into the battery lock and slide it to the left until you hear the battery unlock.
Step 3
- Pull the battery towards you to remove it from the laptop.
Pull the battery towards you to remove it from the laptop.
Step 4
Keyboard
- Using a Phillips #0 screwdriver, remove each of the eighteen 8 mm screws from the bottom of the laptop.
Using a Phillips #0 screwdriver, remove each of the eighteen 8 mm screws from the bottom of the laptop.
Step 5
- Carefully place your fingers underneath the top of the keyboard just below the screen.
- Pull upwards until you can hear the keyboard click out of place.
- Continue around the entire laptop, carefully pulling the keyboard and palm rest assembly slightly from the frame to reveal the ribbon connectors.
- Don’t pull the keyboard off the frame yet because it’s attached by ribbon connectors.
- After the keyboard is detached, unplug each of the three ribbon cables and remove the keyboard and palm rest assembly.
Carefully place your fingers underneath the top of the keyboard just below the screen.
Pull upwards until you can hear the keyboard click out of place.
Continue around the entire laptop, carefully pulling the keyboard and palm rest assembly slightly from the frame to reveal the ribbon connectors.
Don’t pull the keyboard off the frame yet because it’s attached by ribbon connectors.
After the keyboard is detached, unplug each of the three ribbon cables and remove the keyboard and palm rest assembly.
Step 6
CPU Fan
- Before replacing the CPU fan, you’ll have to remove the network card found below the fan.
- Using a Philips #0 screwdriver, remove the two 3 mm screws from the corners of the Wi-Fi card.
- Carefully lift the network card from it’s slot, and disconnect the two coaxial cables.
Before replacing the CPU fan, you’ll have to remove the network card found below the fan.
Using a Philips #0 screwdriver, remove the two 3 mm screws from the corners of the Wi-Fi card.
Carefully lift the network card from it’s slot, and disconnect the two coaxial cables.
Step 7
- The CPU fan can be found in the upper left corner of the laptop.
- Using a Phillips #0 screwdriver, remove the two 4.5 mm screws from the fan.
The CPU fan can be found in the upper left corner of the laptop.
Using a Phillips #0 screwdriver, remove the two 4.5 mm screws from the fan.
Step 8
- Use tweezers to safely remove the fan plug from the motherboard. To remove the plug, gently push left.
Use tweezers to safely remove the fan plug from the motherboard. To remove the plug, gently push left.
Step 9
- Make sure that all fan wires are disconnected from the board.
- Lift the curved end of the fan, and safely remove it.
Make sure that all fan wires are disconnected from the board.
Lift the curved end of the fan, and safely remove it.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Max Piekos
Member since: 03/23/2022
459 Reputation
4 Guides authored
Badges:
7
+4 more badges
Team
UMass Dartmouth, Team B-1, Gurgel Spring 2022
Member of UMass Dartmouth, Team B-1, Gurgel Spring 2022
UMASSD-GURGEL-S22SBG1
4 Members
6 Guides authored