Difficulty
Moderate
Steps
14
Time Required
35 minutes
Sections
5
- Back Cover
- 2 steps
- Battery
- 3 steps
- Hard Drive
- 1 step
- Network Card
- 2 steps
- RAM
- 6 steps
Flags
0
BackAcer Aspire ES1-111M-C7DE
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Unscrew the 13 6.2mm screws located on the bottom of the laptop using the JIS #0 screwdriver.
Unscrew the 13 6.2mm screws located on the bottom of the laptop using the JIS #0 screwdriver.
1024
Step 2
- Using a plastic opening tool, gently pry the lower case off. Place aside.
Using a plastic opening tool, gently pry the lower case off. Place aside.
Step 3
Battery
- Locate the small black button surrounded by a white circle near the battery on the motherboard.
- Press and hold the button for five seconds.
Locate the small black button surrounded by a white circle near the battery on the motherboard.
Press and hold the button for five seconds.
Step 4
- Using your fingers or the small plastic opening tools, disconnect the battery connection from the motherboard by pinching and pulling back on both sides of the connector.
Using your fingers or the small plastic opening tools, disconnect the battery connection from the motherboard by pinching and pulling back on both sides of the connector.
Step 5
- Locate the two 6.2mm black screws holding the battery in place and unscrew them.
- Gently lift and remove the battery.
Locate the two 6.2mm black screws holding the battery in place and unscrew them.
Gently lift and remove the battery.
Step 6
Hard Drive
- Locate the hard drive and slide the hard drive to the left until it disconnects from the mother board.
Locate the hard drive and slide the hard drive to the left until it disconnects from the mother board.
Step 7
Network Card
- You will see a white rectangular piece next to the upper left-hand corner of the motherboard that is connected with a black cord and a white cord; this is the network card.
- Unscrew the one 6.2mm screw in the upper left-hand corner of the network card.
You will see a white rectangular piece next to the upper left-hand corner of the motherboard that is connected with a black cord and a white cord; this is the network card.
Unscrew the one 6.2mm screw in the upper left-hand corner of the network card.
Step 8
- Remove the black and the white cords from the network card.
- Slide the card out of the motherboard and replace it with the new one.
Remove the black and the white cords from the network card.
Slide the card out of the motherboard and replace it with the new one.
Step 9
RAM
- Disconnect the remaining connectors from the motherboard.
Disconnect the remaining connectors from the motherboard.
Step 10
- Unscrew the three 6.2mm screws as indicated by the picture.
Unscrew the three 6.2mm screws as indicated by the picture.
Step 11
- Flip the motherboard over.
Flip the motherboard over.
Step 12
- Locate the RAM
Locate the RAM
Step 13
- Gently push the two metal clips that hold the RAM to the side, as indicated by the picture.
- It should pop up once done.
Gently push the two metal clips that hold the RAM to the side, as indicated by the picture.
It should pop up once done.
Step 14
- Pull the RAM out.
Pull the RAM out.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Mason Devinney
Member since: 09/25/2017
388 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team S3-G1, Cannon Fall 2017
Member of USF Tampa, Team S3-G1, Cannon Fall 2017
USFT-CANNON-F17S3G1
4 Members
6 Guides authored
