Difficulty
Easy
Steps
7
Time Required
5 minutes
Sections
2
- Battery
- 4 steps
- Screen
- 3 steps
Flags
0
BackAcer Aspire ES1-711-P1UV
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Place the laptop face down on a flat, clean surface.
- Remove all twenty-seven 7 mm screws on the back cover of the laptop with a Phillips #0 screwdriver. Screws are circled in red on the diagram.
Place the laptop face down on a flat, clean surface.
Remove all twenty-seven 7 mm screws on the back cover of the laptop with a Phillips #0 screwdriver. Screws are circled in red on the diagram.
1024
Step 2
- Use the iFixit opening tool to pry open the four corners of the back cover of the laptop. You may need to use your hands to fully remove the cover.
- Be sure to evenly apply pressure when removing the back cover.
Use the iFixit opening tool to pry open the four corners of the back cover of the laptop. You may need to use your hands to fully remove the cover.
Be sure to evenly apply pressure when removing the back cover.
Step 3
- Remove the two 5 mm screws located on either side of the battery.
Remove the two 5 mm screws located on either side of the battery.
Step 4
- Disconnect the colored bundled cable connectors from the motherboard. To do this, pull on the wires to disconnect the cable and remove the battery.
Disconnect the colored bundled cable connectors from the motherboard. To do this, pull on the wires to disconnect the cable and remove the battery.
Step 5
Screen
- Place the laptop on a flat surface and open it to see the screen.
- Using your fingers or a plastic opening tool, pry open the bezel that holds the screen in place.
Place the laptop on a flat surface and open it to see the screen.
Using your fingers or a plastic opening tool, pry open the bezel that holds the screen in place.
Step 6
- Use the Phillips #0 screwdriver to remove the fourteen 5mm screws around the screen.
- Use the Phillips #0 screwdriver to remove the four 4mm screws holding in the screen.
- Before unscrewing the screen, place a paper on the keyboard to protect the screen from scratches.
Use the Phillips #0 screwdriver to remove the fourteen 5mm screws around the screen.
Use the Phillips #0 screwdriver to remove the four 4mm screws holding in the screen.
Before unscrewing the screen, place a paper on the keyboard to protect the screen from scratches.
Step 7
- With the screen on the paper, detach the Zero Insertion Force (ZIF) connector attaching the screen to the video cable inside of the front cover.
- To remove the ZIF use your finger to flip up the top cover and gently pull the cable out.
- Be sure to pry open the hinged flap not the connector socket
- Gently remove the screen from laptop.
With the screen on the paper, detach the Zero Insertion Force (ZIF) connector attaching the screen to the video cable inside of the front cover.
To remove the ZIF use your finger to flip up the top cover and gently pull the cable out.
Be sure to pry open the hinged flap not the connector socket
Gently remove the screen from laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Camille Ingham
Member since: 03/22/2018
418 Reputation
2 Guides authored
Badges:
11
+8 more badges
Team
Sam Houston State, Team S17-G3, Blackburne Winter 2018
Member of Sam Houston State, Team S17-G3, Blackburne Winter 2018
SHSU-BLACKBURNE-W18S17G3
1 Member
2 Guides authored
