Acer Aspire One 532H 2527 Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          9 - 15 minutes

Sections

Battery
4 steps
Screen
9 steps

Flags

BackAcer Aspire One 532h-2527
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Press the power button to turn off the netbook.

Press the power button to turn off the netbook.

1024

Step 2

Place the netbook bottom-side-up on a flat surface.
Locate the unlock latch on the top right corner of the back.

Place the netbook bottom-side-up on a flat surface.

Locate the unlock latch on the top right corner of the back.

Step 3

To unlock the battery, slide the lock latch in the direction indicated by the unlocking icon. You should see the orange indicator which means that the latch is unlocked.

To unlock the battery, slide the lock latch in the direction indicated by the unlocking icon. You should see the orange indicator which means that the latch is unlocked.

Step 4

On the opposite side, slide and hold the release latch.
Gently slide the battery out.

On the opposite side, slide and hold the release latch.

Gently slide the battery out.

Step 5

              Screen

Remove the two small circular stickers located on each side at the bottom of the screen.
Once stickers are removed, you should see a Phillips screw head underneath each sticker.

Remove the two small circular stickers located on each side at the bottom of the screen.

Once stickers are removed, you should see a Phillips screw head underneath each sticker.

Step 6

Use the #0 Phillips Screw bit with the Screwdriver to remove the two 6mm Phillips screws from the bottom of the screen.
The screws are located where the stickers were in the previous step.

Use the #0 Phillips Screw bit with the Screwdriver to remove the two 6mm Phillips screws from the bottom of the screen.

The screws are located where the stickers were in the previous step.

Step 7

Using the plastic opening tool, gently separate the front plastic cover from the screen.
You should hear clicks as you go about removing the plastic cover.

Using the plastic opening tool, gently separate the front plastic cover from the screen.

You should hear clicks as you go about removing the plastic cover.

Step 8

Locate the four Phillips screws holding the screen in place.
Using the #0 Phillips Screw bit with the Screwdriver, remove the four 6mm Phillips screws around the screen.

Locate the four Phillips screws holding the screen in place.

Using the #0 Phillips Screw bit with the Screwdriver, remove the four 6mm Phillips screws around the screen.

Step 9

Using the plastic opening tool, gently lift the screen up from the back of the plastic laptop cover.
Use the plastic opening tool to remove the no fuss ribbon connector from the webcam component.

Using the plastic opening tool, gently lift the screen up from the back of the plastic laptop cover.

Use the plastic opening tool to remove the no fuss ribbon connector from the webcam component.

Step 10

Locate the no fuss ribbon connector wire.
Peel it from the backside of the screen.

Locate the no fuss ribbon connector wire.

Peel it from the backside of the screen.

Step 11

Locate the yellow tape on the back of the screen and peel it off partially.
Locate the ZIF (zero insertion force) connector cable.
Carefully unplug the ZIF connector.
No excess force is needed to remove the ZIF connector as its name implies.
Be sure to only pull the connector from its head and not the ribbon wire as it is very delicate.

Locate the yellow tape on the back of the screen and peel it off partially.

Locate the ZIF (zero insertion force) connector cable.

Carefully unplug the ZIF connector.

No excess force is needed to remove the ZIF connector as its name implies.

Be sure to only pull the connector from its head and not the ribbon wire as it is very delicate.

Step 12

Locate the two 6mm screws on each side of the screen.
Use the #0 Phillips Screw bit with the Screwdriver to remove the four 6mm Phillips screws from each side of the screen.

Locate the two 6mm screws on each side of the screen.

Use the #0 Phillips Screw bit with the Screwdriver to remove the four 6mm Phillips screws from each side of the screen.

Step 13

Remove the screen.

Remove the screen.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    Adam Debes

Member since: 09/15/2016

153 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team 11-6, Blackwell Fall 2016                        

                                                  Member of USF Tampa, Team 11-6, Blackwell Fall 2016 



                    USFT-BLACKWELL-F16S11G6                     


                                            3 Members                     


                                            12 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team