Difficulty
Moderate
Steps
15
Time Required
25 - 45 minutes
Sections
5
- Battery
- 2 steps
- Network Card
- 3 steps
- Hard Drive
- 3 steps
- Keyboard
- 2 steps
- Display
- 5 steps
Flags
0
BackAcer Aspire One 751h-1948
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Close the laptop and flip it over to view the back of the laptop.
Close the laptop and flip it over to view the back of the laptop.
1024
Step 2
- Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery.
Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery.
Step 3
Network Card
- Unscrew the two Phillips #0 (M2-L2.5 mm) holding down the network card panel.
- These screws don’t come all the way out.
Unscrew the two Phillips #0 (M2-L2.5 mm) holding down the network card panel.
These screws don’t come all the way out.
Step 4
- Unplug the two connecting cables by lifting them up. They should unclip easily.
Unplug the two connecting cables by lifting them up. They should unclip easily.
Step 5
- Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card.
Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card.
Step 6
Hard Drive
- Unscrew the Phillips 0# (M2 L2.5 mm) screw and remove the cover panel.
- These screws will not come out all the way.
Unscrew the Phillips 0# (M2 L2.5 mm) screw and remove the cover panel.
These screws will not come out all the way.
Step 7
- Remove the hard drive by sliding it to the left and pull it out.
Remove the hard drive by sliding it to the left and pull it out.
Step 8
- Unscrew the Phillips #0 (M2-L2.5 mm) screws.
Unscrew the Phillips #0 (M2-L2.5 mm) screws.
Step 9
Keyboard
- Use the plastic opening tool to push in each of the four clips and carefully lift the keyboard.
- Don’t lift the keyboard completely so that you don’t damage the ribbon cable underneath.
Use the plastic opening tool to push in each of the four clips and carefully lift the keyboard.
Don’t lift the keyboard completely so that you don’t damage the ribbon cable underneath.
Step 10
- When you remove the keyboard, be careful not to damage the ribbon cable that attaches it to the motherboard.
- Unplug the ribbon cable by gently lifting the black tab up. Then remove the cable.
When you remove the keyboard, be careful not to damage the ribbon cable that attaches it to the motherboard.
Unplug the ribbon cable by gently lifting the black tab up. Then remove the cable.
Step 11
Display
- Unplug the SCD cable
Unplug the SCD cable
Step 12
- Use the spudger to remove all rubber pads covering the screws for the upper casing.
- Then unscrew all the Phillips #0 (M2-L5 mm) screws under rubber pads.
Use the spudger to remove all rubber pads covering the screws for the upper casing.
Then unscrew all the Phillips #0 (M2-L5 mm) screws under rubber pads.
Step 13
- Separate the upper casing from the display.
Separate the upper casing from the display.
Step 14
- Unscrew all the Phillips 0# (M2-L2.5 mm) on each side of the display.
Unscrew all the Phillips 0# (M2-L2.5 mm) on each side of the display.
Step 15
- Separate the screen from the metal frame that secures it to the upper casing and remove the screen.
- Be careful, the display is very sensitive.
Separate the screen from the metal frame that secures it to the upper casing and remove the screen.
Be careful, the display is very sensitive.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Chris Bolton
Member since: 03/22/2017
434 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
UMass Dartmouth, Team S8-G2, Catania Spring 2017
Member of UMass Dartmouth, Team S8-G2, Catania Spring 2017
UMASSD-CATANIA-S17S8G2
3 Members
8 Guides authored
