Difficulty

Moderate

Steps

17

Time Required

                          25 - 30 minutes

Sections

6

  • Battery
  • 2 steps
  • Network Card
  • 3 steps
  • Hard Drive
  • 3 steps
  • Keyboard
  • 2 steps
  • Front Panel
  • 4 steps
  • Fan
  • 3 steps

Flags

0

  • BackAcer Aspire One 751h-1948

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Close the laptop and flip it over to view the back of the laptop.

Close the laptop and flip it over to view the back of the laptop.

1024

Step 2

  • Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery.

Unlock the right side of the battery by sliding the battery lock to the right. Then slide the left lock to the left and remove the battery.

Step 3

              Network Card
  • Unscrew the two Phillips #0 (M2-L2.5 mm) holding down the network card panel.
  • These screws don’t come all the way out.

Unscrew the two Phillips #0 (M2-L2.5 mm) holding down the network card panel.

These screws don’t come all the way out.

Step 4

  • Unplug the two connecting cables by lifting them up. They should unclip easily.

Unplug the two connecting cables by lifting them up. They should unclip easily.

Step 5

  • Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card.

Remove the screw Phillips #0 (M2-L3 mm) holding down the network card. Pull out the card.

Step 6

              Hard Drive
  • Unscrew the Phillips 0# (M2 L2.5 mm) screw and remove the cover panel.
  • These screws will not come out all the way.

Unscrew the Phillips 0# (M2 L2.5 mm) screw and remove the cover panel.

These screws will not come out all the way.

Step 7

  • Remove the hard drive by sliding it to the left and pull it out.

Remove the hard drive by sliding it to the left and pull it out.

Step 8

  • Unscrew the Phillips #0 (M2-L2.5 mm) screws.

Unscrew the Phillips #0 (M2-L2.5 mm) screws.

Step 9

              Keyboard
  • Use the plastic opening tool to push in each of the four clips and carefully lift the keyboard.
  • Don’t lift the keyboard completely so that you don’t damage the ribbon cable underneath.

Use the plastic opening tool to push in each of the four clips and carefully lift the keyboard.

Don’t lift the keyboard completely so that you don’t damage the ribbon cable underneath.

Step 10

  • When you remove the keyboard, be careful not to damage the ribbon cable that attaches it to the motherboard.
  • Unplug the ribbon cable by gently lifting the black tab up. Then remove the cable.

When you remove the keyboard, be careful not to damage the ribbon cable that attaches it to the motherboard.

Unplug the ribbon cable by gently lifting the black tab up. Then remove the cable.

Step 11

              Front Panel
  • Use the screwdriver to remove all the Phillips #00 (M2-L2.5 mm) screws shown here.

Use the screwdriver to remove all the Phillips #00 (M2-L2.5 mm) screws shown here.

Step 12

  • Flip the laptop over and remove all the Phillips #0 (M2-L5 mm) screws under the keyboard.
  • Remove all the Phillips #0 (M2-L2.5 mm) screws

Flip the laptop over and remove all the Phillips #0 (M2-L5 mm) screws under the keyboard.

Remove all the Phillips #0 (M2-L2.5 mm) screws

Step 13

  • Lift the small black clip and remove the ribbon cable before proceeding.

Lift the small black clip and remove the ribbon cable before proceeding.

Step 14

  • Separate the front panel from the back panel, by sliding your thumb nail between them.

Separate the front panel from the back panel, by sliding your thumb nail between them.

Step 15

              Fan
  • Use the screwdriver to remove Phillips #0 (M2-L5 mm) screws

Use the screwdriver to remove Phillips #0 (M2-L5 mm) screws

Step 16

  • Remove the ribbon cable that sits on top of the fan by lifting the small black clip and pulling the blue tab.
  • Use the same technique to remove the ribbon cable from the motherboard.

Remove the ribbon cable that sits on top of the fan by lifting the small black clip and pulling the blue tab.

Use the same technique to remove the ribbon cable from the motherboard.

Step 17

  • Unscrew the Phillips #0 (M2-L2.5 mm) screw from the fan, and remove the fan.

Unscrew the Phillips #0 (M2-L2.5 mm) screw from the fan, and remove the fan.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Chris Bolton

Member since: 03/22/2017

434 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       UMass Dartmouth, Team S8-G2, Catania Spring 2017                        

                                                  Member of UMass Dartmouth, Team S8-G2, Catania Spring 2017 



                    UMASSD-CATANIA-S17S8G2                     


                                            3 Members                     


                                            8 Guides authored