Acer Aspire One A150 1672 Display Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          25 minutes

Sections

Front-facing Camera
5 steps
Display Screen
5 steps

Flags

BackAcer Aspire One A150-1672
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Front-facing Camera

With your fingers, remove 6 rubber coverings located at the edges of screen. The rubber coverings are held in place with a small amount of adhesive, but you should be able to peel them off easily.
There are 4 coverings on the top (circular shaped) and 2 on the bottom (half-oval shaped).

With your fingers, remove 6 rubber coverings located at the edges of screen. The rubber coverings are held in place with a small amount of adhesive, but you should be able to peel them off easily.

There are 4 coverings on the top (circular shaped) and 2 on the bottom (half-oval shaped).

1024

Step 2

Using a Phillips #1 screwdriver, unscrew the six 5.2mm screws in the places where the rubber coverings were located.

Using a Phillips #1 screwdriver, unscrew the six 5.2mm screws in the places where the rubber coverings were located.

Step 3

Slide the spudger between the thin gap located between the white and pink plastic casing at the top.
Move the spudger from the right side to the left to detach the white plastic frame from the pink plastic casing.
Remove the white frame by pulling it towards yourself.
It may take considerable force to initially slide the spudger between the white and pink parts of the casing.

Slide the spudger between the thin gap located between the white and pink plastic casing at the top.

Move the spudger from the right side to the left to detach the white plastic frame from the pink plastic casing.

Remove the white frame by pulling it towards yourself.

It may take considerable force to initially slide the spudger between the white and pink parts of the casing.

Step 4

At the top of the display screen, pull the brown connector towards the right with your right hand while holding on to the black piece of electrical tape next to the white connector with your left hand to disconnect the two connectors from each other.
Gently pull the display screen towards you to more easily access the cable behind the screen.

At the top of the display screen, pull the brown connector towards the right with your right hand while holding on to the black piece of electrical tape next to the white connector with your left hand to disconnect the two connectors from each other.

Gently pull the display screen towards you to more easily access the cable behind the screen.

Step 5

Use the spudger to detach the piece of tape from the camera by sliding it between the camera and tape.
Pull the camera towards you to remove it.

Use the spudger to detach the piece of tape from the camera by sliding it between the camera and tape.

Pull the camera towards you to remove it.

Step 6

              Display Screen

Disconnect the microphone, which located left of the camera piece, by pinching the tape around the wires, pinching the microphone, and pulling the two in opposite directions. This microphone is detached in the same way the camera was detached.

Disconnect the microphone, which located left of the camera piece, by pinching the tape around the wires, pinching the microphone, and pulling the two in opposite directions. This microphone is detached in the same way the camera was detached.

Step 7

Using a Philips Head #1 screwdriver, remove the four 4.63 mm screws located on both sides of the display screen.
Pull the display screen towards you to remove it from the plastic cover of the netbook.

Using a Philips Head #1 screwdriver, remove the four 4.63 mm screws located on both sides of the display screen.

Pull the display screen towards you to remove it from the plastic cover of the netbook.

Step 8

Gently peel off the black wire connected to both the microphone and the camera. This is attached with a small amount of adhesive to the back of the display screen.

Gently peel off the black wire connected to both the microphone and the camera. This is attached with a small amount of adhesive to the back of the display screen.

Step 9

Pull up the transparent piece of tape at the bottom of the display screen that holds the cord in place.

Pull up the transparent piece of tape at the bottom of the display screen that holds the cord in place.

Step 10

Detach the cord by pulling the cord out of the slot of the green circuit on the bottom of the laptop. Once the cord is detached, the display screen will be unattached and able to be removed.

Detach the cord by pulling the cord out of the slot of the green circuit on the bottom of the laptop. Once the cord is detached, the display screen will be unattached and able to be removed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Connor Watkins

Member since: 10/30/2016

261 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Baylor, Team 4-3, Williams Fall 2016                        

                                                  Member of Baylor, Team 4-3, Williams Fall 2016 



                    BU-WILLIAMS-F16S4G3                     


                                            3 Members                     


                                            8 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team