Difficulty
Moderate
Steps
10
Time Required
10 - 20 minutes
Sections
2
- Battery
- 5 steps
- Keyboard
- 5 steps
Flags
0
BackAcer Aspire R R5-471T-51UN
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Step 5 asks you to be cautious in gently removing the battery of the laptop. From there, you will be asked to remove the motherboard, the fan, and finally the display brackets.
Before getting started, power off your device and disconnect from any other external connections.
What you need
Step 1
Battery
- Flip your laptop over so the bottom is facing you.
- Remove the twelve 5 mm screws with a Phillips #0 screwdriver.
Flip your laptop over so the bottom is facing you.
Remove the twelve 5 mm screws with a Phillips #0 screwdriver.
1024
Step 2
- Insert the Jimmy between the back cover of the laptop and the base of the laptop and then slowly use the Jimmy to pry off the back cover of the laptop.
Insert the Jimmy between the back cover of the laptop and the base of the laptop and then slowly use the Jimmy to pry off the back cover of the laptop.
Step 3
- Use your Phillips #0 screwdriver to remove the two 3mm screws on the battery.
Use your Phillips #0 screwdriver to remove the two 3mm screws on the battery.
Step 4
- Gently and cautiously pinch the white ends of the battery connector cable and slowly pull it from the motherboard.
Gently and cautiously pinch the white ends of the battery connector cable and slowly pull it from the motherboard.
Step 5
- Gently lift the battery out of the laptop.
- Be cautious with the lithium ion battery as you remove it.
Gently lift the battery out of the laptop.
Be cautious with the lithium ion battery as you remove it.
Step 6
Keyboard
- Use the spudger to flip up the locking tabs on each of the four ZIF cable connectors.
- Remove each of the ribbon cables from their connectors.
Use the spudger to flip up the locking tabs on each of the four ZIF cable connectors.
Remove each of the ribbon cables from their connectors.
Step 7
- Using the Phillips #0 screwdriver, remove the eight 3 mm screws holding in the motherboard and the three 3 mm screws holding down the fan.
Using the Phillips #0 screwdriver, remove the eight 3 mm screws holding in the motherboard and the three 3 mm screws holding down the fan.
Step 8
- Remove the motherboard and the fan by gently pulling them out of the assembly.
- Using the Phillips #0 screwdriver, remove the three 3 mm screws holding down the daughterboard and gently pull it up and out of the assembly.
Remove the motherboard and the fan by gently pulling them out of the assembly.
Using the Phillips #0 screwdriver, remove the three 3 mm screws holding down the daughterboard and gently pull it up and out of the assembly.
Step 9
- Using the Phillips #0 screwdriver, remove the eight 5 mm screws from the display brackets on either side.
Using the Phillips #0 screwdriver, remove the eight 5 mm screws from the display brackets on either side.
Step 10
- Remove the keyboard assembly by gently pulling it up.
Remove the keyboard assembly by gently pulling it up.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
John Sandor
Member since: 01/26/2020
688 Reputation
5 Guides authored
Badges:
6
+3 more badges
Team
Embry-Riddle Aeronautical University, Team S3-G3, Watkins Spring 2020
Member of Embry-Riddle Aeronautical University, Team S3-G3, Watkins Spring 2020
ERAU-WATKINS-S20S3G3
4 Members
5 Guides authored
