Acer Aspire S3 951 6432 Hard Drive Hdd Sdd Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          10 minutes

Sections

Battery
5 steps
Hard Drive (HDD/SDD)
5 steps

Flags

BackAcer Aspire S3-951-6432
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Keeping it closed, turn the laptop upside down.
With the Phillips #0 screwdriver, remove the twelve 5 mm screws that hold the laptop together.
Insert the plastic opening tool between the plastic casings to pull the bottom lid of the laptop up.
You do not need to pull the lid all the way off.

Keeping it closed, turn the laptop upside down.

With the Phillips #0 screwdriver, remove the twelve 5 mm screws that hold the laptop together.

Insert the plastic opening tool between the plastic casings to pull the bottom lid of the laptop up.

You do not need to pull the lid all the way off.

1024

Step 2

Locate the six cables that are connected to the motherboard. The cable with the white strip is located underneath the cable with the orange strip.
Using the plastic opening tool on one side and your fingernail on the other, wedge each cable out of its socket.
The battery is now disconnected. If you want to remove the battery, follow the remaining steps in this guide. However, if you only wish to disconnect the battery to do other internal work, skip the remaining steps in this guide and continue on to other guides.

Locate the six cables that are connected to the motherboard. The cable with the white strip is located underneath the cable with the orange strip.

Using the plastic opening tool on one side and your fingernail on the other, wedge each cable out of its socket.

The battery is now disconnected. If you want to remove the battery, follow the remaining steps in this guide. However, if you only wish to disconnect the battery to do other internal work, skip the remaining steps in this guide and continue on to other guides.

Step 3

With the Phillips #0 screwdriver, remove the two 5 mm screws that are located above the long black piece of the battery.

With the Phillips #0 screwdriver, remove the two 5 mm screws that are located above the long black piece of the battery.

Step 4

Locate the two speakers for this laptop that are connected above the battery by a thin red cord.
Using the Phillips #0 screwdriver, remove the two 3 mm screws holding the left speaker in place.
Pull the left speaker up along with the red cord and leave it off to the right side.
If you plan to disassemble the laptop down to the motherboard, you will also need to remove the two 3 mm screws holding the right-side speaker in place with a Phillips #0 screwdriver.

Locate the two speakers for this laptop that are connected above the battery by a thin red cord.

Using the Phillips #0 screwdriver, remove the two 3 mm screws holding the left speaker in place.

Pull the left speaker up along with the red cord and leave it off to the right side.

If you plan to disassemble the laptop down to the motherboard, you will also need to remove the two 3 mm screws holding the right-side speaker in place with a Phillips #0 screwdriver.

Step 5

Without bending it, lift the entire battery (both the long black piece and the rectangular blue piece) straight up. Place it off to one side.

Without bending it, lift the entire battery (both the long black piece and the rectangular blue piece) straight up. Place it off to one side.

Step 6

              Hard Drive (HDD/SDD)

Locate the hard drive, which is the black rectangular object just above the battery.

Locate the hard drive, which is the black rectangular object just above the battery.

Step 7

Lift the silver and yellow cable next to the hard drive up with the spudger.

Lift the silver and yellow cable next to the hard drive up with the spudger.

Step 8

Underneath the yellow cable, there is another gray and black cable.
Use your fingernails to pull the gray and black cable out of its connector.

Underneath the yellow cable, there is another gray and black cable.

Use your fingernails to pull the gray and black cable out of its connector.

Step 9

Pull on the blue tab near the hard drive to remove the connector for the motherboard.

Pull on the blue tab near the hard drive to remove the connector for the motherboard.

Step 10

Using a Phillips #0 screwdriver, remove the single 3 mm screw from the top of the hard drive sled.
Lift the rectangular tab to pull the hard drive out of the laptop .

Using a Phillips #0 screwdriver, remove the single 3 mm screw from the top of the hard drive sled.

Lift the rectangular tab to pull the hard drive out of the laptop .

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Cynthia Bennett

Member since: 10/17/2018

569 Reputation

                                      5 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       UW Tacoma, Team S1-G1, Rose Fall 2018                        

                                                  Member of UW Tacoma, Team S1-G1, Rose Fall 2018 



                    UWT-ROSE-F18S1G1                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team