Difficulty
Easy
Steps
9
Time Required
8 minutes
Sections
5
- Lower Back Panel
- 1 step
- RAM
- 1 step
- Keyboard
- 4 steps
- Battery
- 2 steps
- Optical Drive
- 1 step
Flags
0
BackAcer Aspire TimelineX 4830T-6682
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Back Panel
- Remove the single screw with a Phillips #0 screwdriver.
- Use a plastic opening tool on the upper part of the panel to remove it and access the RAM.
- The other way to remove the panel is by sliding it away from the laptop. The difficulty of sliding it depends on the condition of your laptop.
Remove the single screw with a Phillips #0 screwdriver.
Use a plastic opening tool on the upper part of the panel to remove it and access the RAM.
The other way to remove the panel is by sliding it away from the laptop. The difficulty of sliding it depends on the condition of your laptop.
1024
Step 2
RAM
- After the panel has been removed, locate the RAM. It should be on the lower right.
- There are pins around the RAM that need to be pulled back. After the pins are removed, pull the RAM chip towards you to remove it.
After the panel has been removed, locate the RAM. It should be on the lower right.
There are pins around the RAM that need to be pulled back. After the pins are removed, pull the RAM chip towards you to remove it.
Step 3
Keyboard
- Remove the eleven screws that hold that back panel to the laptop using a J0 Phillips screwdriver bit.
Remove the eleven screws that hold that back panel to the laptop using a J0 Phillips screwdriver bit.
Step 4
- Place the laptop in the upright position, the lower front touchpad panel should be easily detatched at this point.
- Remove the lower front touchpad panel by using an angled tweezers to disconnect the only wired tape connected to the motherboard.
Place the laptop in the upright position, the lower front touchpad panel should be easily detatched at this point.
Remove the lower front touchpad panel by using an angled tweezers to disconnect the only wired tape connected to the motherboard.
Step 5
- Next, disconnect the 4 wired tapes of the keyboard from the motherboard just like we did with the lower front touchpad panel.
Next, disconnect the 4 wired tapes of the keyboard from the motherboard just like we did with the lower front touchpad panel.
Step 6
- Finally, using an opening tool, gently pry along the edge of the keyboard to separate it from the laptop.
Finally, using an opening tool, gently pry along the edge of the keyboard to separate it from the laptop.
Step 7
Battery
- The battery will be on the side closest to the screen.
- Gently lift it out. It will still be attached by white, red, and black wires.
The battery will be on the side closest to the screen.
Gently lift it out. It will still be attached by white, red, and black wires.
Step 8
- Pull the white plug, it should easily detach.
- Remove the battery from the device.
Pull the white plug, it should easily detach.
Remove the battery from the device.
Step 9
Optical Drive
- Elevate the optical drive to get a good grip, then slide the drive horizontally away from the laptop, disconnecting it from the motherboard
Elevate the optical drive to get a good grip, then slide the drive horizontally away from the laptop, disconnecting it from the motherboard
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Jon Brunsell
Member since: 07/10/2019
592 Reputation
6 Guides authored
Badges:
8
+5 more badges
Team
IUPUI, Team S1-G1, Beck Spring 2020
Member of IUPUI, Team S1-G1, Beck Spring 2020
IUPUI-BECK-S20S1G1
3 Members
6 Guides authored
