Difficulty
Moderate
Steps
10
Time Required
15 minutes
Sections
3
- Lower Back Panel
- 1 step
- Keyboard
- 4 steps
- Power Plug
- 5 steps
Flags
0
BackAcer Aspire TimelineX 4830T-6682
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lower Back Panel
- Remove the single screw with a Phillips #0 screwdriver.
- Use a plastic opening tool on the upper part of the panel to remove it and access the RAM.
- The other way to remove the panel is by sliding it away from the laptop. The difficulty of sliding it depends on the condition of your laptop.
Remove the single screw with a Phillips #0 screwdriver.
Use a plastic opening tool on the upper part of the panel to remove it and access the RAM.
The other way to remove the panel is by sliding it away from the laptop. The difficulty of sliding it depends on the condition of your laptop.
1024
Step 2
Keyboard
- Remove the eleven screws that hold that back panel to the laptop using a J0 Phillips screwdriver bit.
Remove the eleven screws that hold that back panel to the laptop using a J0 Phillips screwdriver bit.
Step 3
- Place the laptop in the upright position, the lower front touchpad panel should be easily detatched at this point.
- Remove the lower front touchpad panel by using an angled tweezers to disconnect the only wired tape connected to the motherboard.
Place the laptop in the upright position, the lower front touchpad panel should be easily detatched at this point.
Remove the lower front touchpad panel by using an angled tweezers to disconnect the only wired tape connected to the motherboard.
Step 4
- Next, disconnect the 4 wired tapes of the keyboard from the motherboard just like we did with the lower front touchpad panel.
Next, disconnect the 4 wired tapes of the keyboard from the motherboard just like we did with the lower front touchpad panel.
Step 5
- Finally, using an opening tool, gently pry along the edge of the keyboard to separate it from the laptop.
Finally, using an opening tool, gently pry along the edge of the keyboard to separate it from the laptop.
Step 6
Power Plug
- The power connector is easy to spot once you have removed the keyboard.
The power connector is easy to spot once you have removed the keyboard.
Step 7
- Slide the DVD drive out of the computer to gain access to the cables
Slide the DVD drive out of the computer to gain access to the cables
Step 8
- The rubber block is attached with a mild adhesive. Use the spudger tool to loosen it
- Once the block is loose, use the spudger to unhook the wires from their guides.
The rubber block is attached with a mild adhesive. Use the spudger tool to loosen it
Once the block is loose, use the spudger to unhook the wires from their guides.
Step 9
- The body of the plug is glued to the computer. Use the spudger tool to wiggle the plug until it comes loose.
The body of the plug is glued to the computer. Use the spudger tool to wiggle the plug until it comes loose.
Step 10
- Use gentle pressure to pull the plug from its socket on the motherboard. Once the plug is loose, you can pull the entire plug assembly from the computer.
Use gentle pressure to pull the plug from its socket on the motherboard. Once the plug is loose, you can pull the entire plug assembly from the computer.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Max Scharnhorst
Member since: 09/25/2017
118 Reputation
1 Guide authored
Badges:
6
+3 more badges
Team
University of North Texas, Team S3-G6, Thompson Fall 2017
Member of University of North Texas, Team S3-G6, Thompson Fall 2017
UNT-THOMPSON-F17S3G6
4 Members
5 Guides authored
