Difficulty

Difficult

Steps

10

Time Required

                          30 minutes - 1 hour

Sections

2

  • Battery
  • 5 steps
  • Display
  • 5 steps

Flags

0

  • BackAcer Aspire V5-122P-0468

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Remove the nine 4mm screws with a PH0 screwdriver.
  • Remove the two 6mm screws with a PH0 screwdriver.

Remove the nine 4mm screws with a PH0 screwdriver.

Remove the two 6mm screws with a PH0 screwdriver.

1024

Step 2

  • Remove the black rubber tab on the back of the computer
  • Remove the 4mm screw hidden underneath the black tab with a PH0 screwdriver.

Remove the black rubber tab on the back of the computer

Remove the 4mm screw hidden underneath the black tab with a PH0 screwdriver.

Step 3

  • Orient the computer upside down, with the hinges facing away from you.
  • Find the black plastic piece in the SD card slot on the right side of the computer.
  • Remove the plastic piece by sliding it out of the SD card slot.

Orient the computer upside down, with the hinges facing away from you.

Find the black plastic piece in the SD card slot on the right side of the computer.

Remove the plastic piece by sliding it out of the SD card slot.

Step 4

  • Insert a spudger at these eight locations to disengage the plastic tabs from the housing cover, and pry apart.
  • Continue around the entire perimeter of the cover with the spudger.
  • Use a spudger to pry the cover around I/O ports.

Insert a spudger at these eight locations to disengage the plastic tabs from the housing cover, and pry apart.

Continue around the entire perimeter of the cover with the spudger.

Use a spudger to pry the cover around I/O ports.

Step 5

  • Remove the two 4mm screws using a PH0 screwdriver.
  • Depress the tabs holding the battery with a spudger.
  • Disconnect the battery connector from the motherboard using a spudger.
  • Pull the battery up and away from the laptop to remove.

Remove the two 4mm screws using a PH0 screwdriver.

Depress the tabs holding the battery with a spudger.

Disconnect the battery connector from the motherboard using a spudger.

Pull the battery up and away from the laptop to remove.

Step 6

              Display
  • Flip up the black locking tab on the ZIF connector, and pull out the ribbon cable.

Flip up the black locking tab on the ZIF connector, and pull out the ribbon cable.

Step 7

  • Wedge a spudger in between the plastic bezel frame and back cover to create a gap.
  • Then insert a plastic opening tool to pry apart the bezel from the back cover.
  • Work your way around the perimeter of the cover with the plastic opening tool.

Wedge a spudger in between the plastic bezel frame and back cover to create a gap.

Then insert a plastic opening tool to pry apart the bezel from the back cover.

Work your way around the perimeter of the cover with the plastic opening tool.

Step 8

  • Open up the laptop to unsnap the hinges from the back of the computer.
  • Slide the pin connector and cable through the hinge that connects the display to the rest of the laptop.

Open up the laptop to unsnap the hinges from the back of the computer.

Slide the pin connector and cable through the hinge that connects the display to the rest of the laptop.

Step 9

  • Remove the transparent tape covering the pin connector.
  • Unplug the pin connector from the display.

Remove the transparent tape covering the pin connector.

Unplug the pin connector from the display.

Step 10

  • Cut the tape between the display and the plastic frame using the flat end of a spudger.
  • Work the spudger around the perimeter of the display to separate it from the bezel.
  • The display is attached with a strong adhesive. Applying heat with a hairdryer or heat gun may make the removal process easier.

Cut the tape between the display and the plastic frame using the flat end of a spudger.

Work the spudger around the perimeter of the display to separate it from the bezel.

The display is attached with a strong adhesive. Applying heat with a hairdryer or heat gun may make the removal process easier.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors 


                    Nat McCormick

Member since: 02/15/2018

801 Reputation

                                      5 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges

Team

                       USF Tampa, Team S16-G1, Boczar Spring 2018                        

                                                  Member of USF Tampa, Team S16-G1, Boczar Spring 2018 



                    USFT-BOCZAR-S18S16G1                     


                                            5 Members                     


                                            10 Guides authored