Difficulty
Moderate
Steps
10
Time Required
10 - 20 minutes
Sections
2
- Battery
- 5 steps
- Touchpad
- 5 steps
Flags
0
BackAcer Aspire V5-122P-0468
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Remove the nine 4mm screws with a PH0 screwdriver.
- Remove the two 6mm screws with a PH0 screwdriver.
Remove the nine 4mm screws with a PH0 screwdriver.
Remove the two 6mm screws with a PH0 screwdriver.
1024
Step 2
- Remove the black rubber tab on the back of the computer
- Remove the 4mm screw hidden underneath the black tab with a PH0 screwdriver.
Remove the black rubber tab on the back of the computer
Remove the 4mm screw hidden underneath the black tab with a PH0 screwdriver.
Step 3
- Orient the computer upside down, with the hinges facing away from you.
- Find the black plastic piece in the SD card slot on the right side of the computer.
- Remove the plastic piece by sliding it out of the SD card slot.
Orient the computer upside down, with the hinges facing away from you.
Find the black plastic piece in the SD card slot on the right side of the computer.
Remove the plastic piece by sliding it out of the SD card slot.
Step 4
- Insert a spudger at these eight locations to disengage the plastic tabs from the housing cover, and pry apart.
- Continue around the entire perimeter of the cover with the spudger.
- Use a spudger to pry the cover around I/O ports.
Insert a spudger at these eight locations to disengage the plastic tabs from the housing cover, and pry apart.
Continue around the entire perimeter of the cover with the spudger.
Use a spudger to pry the cover around I/O ports.
Step 5
- Remove the two 4mm screws using a PH0 screwdriver.
- Depress the tabs holding the battery with a spudger.
- Disconnect the battery connector from the motherboard using a spudger.
- Pull the battery up and away from the laptop to remove.
Remove the two 4mm screws using a PH0 screwdriver.
Depress the tabs holding the battery with a spudger.
Disconnect the battery connector from the motherboard using a spudger.
Pull the battery up and away from the laptop to remove.
Step 6
Touchpad
- Use the spudger to pop up the latch on the ZIF connector.
- Pull out the ribbon cable.
Use the spudger to pop up the latch on the ZIF connector.
Pull out the ribbon cable.
Step 7
- Remove the three 2mm PH #0 screws.
- Lift the metal tape up and off of the mounting bracket.
Remove the three 2mm PH #0 screws.
Lift the metal tape up and off of the mounting bracket.
Step 8
- Remove the metal mounting bracket from the bottom of the touchpad
Remove the metal mounting bracket from the bottom of the touchpad
Step 9
- Carefully remove the foam pad from along the top edge of touchpad using a spudger.
- This pad can be reused.
- Remove the four 2mm PH #0 screws.
Carefully remove the foam pad from along the top edge of touchpad using a spudger.
This pad can be reused.
Remove the four 2mm PH #0 screws.
Step 10
- Remove the touchpad from the laptop using a spudger.
Remove the touchpad from the laptop using a spudger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Nat McCormick
Member since: 02/15/2018
801 Reputation
5 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team S16-G1, Boczar Spring 2018
Member of USF Tampa, Team S16-G1, Boczar Spring 2018
USFT-BOCZAR-S18S16G1
5 Members
10 Guides authored
