Difficulty
Moderate
Steps
13
Time Required
10 minutes
Sections
3
- Battery
- 2 steps
- Keyboard
- 5 steps
- Hard Disk Drive (HDD)
- 6 steps
Flags
0
BackAcer Aspire V5-571-6891
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Use the pointed end of the spudger to slide the battery lock until the battery pops loose.
Use the pointed end of the spudger to slide the battery lock until the battery pops loose.
1024
Step 2
- Slide the battery out of the battery slot.
Slide the battery out of the battery slot.
Step 3
Keyboard
- Remove the two 6mm PH1 screws from the bottom of the laptop.
Remove the two 6mm PH1 screws from the bottom of the laptop.
Step 4
- Use the spudger, push the two tabs, located in the battery slot, through their slots to release the keyboard.
- Do this with the computer slightly open for ease.
Use the spudger, push the two tabs, located in the battery slot, through their slots to release the keyboard.
Do this with the computer slightly open for ease.
Step 5
- Open the laptop.
- Start top of the keyboard and use the opening tool to pop the remaining tabs around the keyboard loose.
- The keyboard can be flipped onto its face once removed.
Open the laptop.
Start top of the keyboard and use the opening tool to pop the remaining tabs around the keyboard loose.
The keyboard can be flipped onto its face once removed.
Step 6
- Use the spudger and slide the grey tabs on either side of the keyboard wires away from the white plastic.
Use the spudger and slide the grey tabs on either side of the keyboard wires away from the white plastic.
Step 7
- Disconnect the keyboard by pulling the blue tape on the wire strip.
Disconnect the keyboard by pulling the blue tape on the wire strip.
Step 8
Hard Disk Drive (HDD)
- Remove the five 6mm PH1 screws beneath the keyboard.
Remove the five 6mm PH1 screws beneath the keyboard.
Step 9
- Use the spudger to pop the gray tab up and away from the far left wire strip.
- Disconnect the wire strip by pulling the blue tab loose.
Use the spudger to pop the gray tab up and away from the far left wire strip.
Disconnect the wire strip by pulling the blue tab loose.
Step 10
- Use the spudger to pop the white tab up away from the wire strip located at the top left corner of the mouse pad.
- Disconnect the wire strip by pulling the blue tab.
Use the spudger to pop the white tab up away from the wire strip located at the top left corner of the mouse pad.
Disconnect the wire strip by pulling the blue tab.
Step 11
- Close the laptop.
- Remove the remaining 18 6mm PH1 screws from the bottom cover of the laptop.
Close the laptop.
Remove the remaining 18 6mm PH1 screws from the bottom cover of the laptop.
Step 12
- Use the opening tool to separate the back of the laptop from the inside cover.
- Open the computer and remove the inside cover.
Use the opening tool to separate the back of the laptop from the inside cover.
Open the computer and remove the inside cover.
Step 13
- Lift the HDD out of the base and use the opening tool to disconnect the HDD from the motherboard wire.
Lift the HDD out of the base and use the opening tool to disconnect the HDD from the motherboard wire.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Lakbira Sheffield
Member since: 01/29/2018
673 Reputation
4 Guides authored
Badges:
13
+10 more badges
Team
University of Alabama, Team S2-G7, Bedsole Spring 2018
Member of University of Alabama, Team S2-G7, Bedsole Spring 2018
UA-BEDSOLE-S18S2G7
3 Members
12 Guides authored
