Acer Aspire V5 571P 6609 Display Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          1 hour

Sections

Display Replacement
13 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackACER Aspire V5-571P-6609
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Display Replacement

Start by placing laptop on non-static surface and powering off completely. Apply static resistant wristband.

Start by placing laptop on non-static surface and powering off completely. Apply static resistant wristband.

1024

Step 2

Use a pointed tool (we used a screwdriver) to slide release to the right when facing laptop from non-battery side.
Gently pull battery away from laptop with slide release held open.

Use a pointed tool (we used a screwdriver) to slide release to the right when facing laptop from non-battery side.

Gently pull battery away from laptop with slide release held open.

Step 3

Remove all twenty 6.7 mm Phillips #0 screws from the bottom side of the laptop.
Turn the laptop over and open the lid.

Remove all twenty 6.7 mm Phillips #0 screws from the bottom side of the laptop.

Turn the laptop over and open the lid.

Step 4

Use a Jimmy tool to slide between the keyboard and top panel. Gently pop the tabs out of their slots and the keyboard will come loose. DO NOT PULL KEYBOARD OUT YET.
Before you lift the keyboard out of place, note the two flat flex cables for the key input and keyboard backlights. One is larger that the other. Lift keyboard just high enough to gently release them from the two ports seen here with a non-static tweezers.
Once cables are safely detached, lift keyboard off of laptop and place on safe, non-static surface.

Use a Jimmy tool to slide between the keyboard and top panel. Gently pop the tabs out of their slots and the keyboard will come loose. DO NOT PULL KEYBOARD OUT YET.

Before you lift the keyboard out of place, note the two flat flex cables for the key input and keyboard backlights. One is larger that the other. Lift keyboard just high enough to gently release them from the two ports seen here with a non-static tweezers.

Once cables are safely detached, lift keyboard off of laptop and place on safe, non-static surface.

Step 5

Use a Phillips #0 screwdriver to remove the six screws.
Flip up the block lock bars on the two ZIF connectors, then gently disconnect the two ribbon cables.

Use a Phillips #0 screwdriver to remove the six screws.

Flip up the block lock bars on the two ZIF connectors, then gently disconnect the two ribbon cables.

Step 6

Slide the Jimmy Tool in between front and back panel of the laptop.
Slowly rotate the Jimmy tool, prying until the top panel pops loose. Repeat on all sides until the top panel is free of main body.
Gently lift top panel free of main body. You now have access to the Motherboard.

Slide the Jimmy Tool in between front and back panel of the laptop.

Slowly rotate the Jimmy tool, prying until the top panel pops loose. Repeat on all sides until the top panel is free of main body.

Gently lift top panel free of main body. You now have access to the Motherboard.

Step 7

Once the top panel is removed, lift the tape that holds the power cable for the fan.
Gently pull fan power cable out.
Use tweezers to gently pull charging port out of place.

Once the top panel is removed, lift the tape that holds the power cable for the fan.

Gently pull fan power cable out.

Use tweezers to gently pull charging port out of place.

Step 8

Use tweezers to gently detach black and white Wi-Fi card cables shown here by lifting up until they pop off.
Once both cables are detached, unscrew the single screw holding Wireless LAN card in place.
The Wi-Fi card should lift up slightly on its own. Use tweezers to gently lift the Wi-Fi card out at a 45 degree angle to prevent damage.

Use tweezers to gently detach black and white Wi-Fi card cables shown here by lifting up until they pop off.

Once both cables are detached, unscrew the single screw holding Wireless LAN card in place.

The Wi-Fi card should lift up slightly on its own. Use tweezers to gently lift the Wi-Fi card out at a 45 degree angle to prevent damage.

Step 9

Remove the two Phillips #0 screws that hold in the battery port.

Remove the two Phillips #0 screws that hold in the battery port.

Step 10

Gently pull the optical drive out.
This should slide out easily by gently sliding the disc drive outwards on its rails.

Gently pull the optical drive out.

This should slide out easily by gently sliding the disc drive outwards on its rails.

Step 11

Place fingertips on edges of motherboard to prevent damage to the circuitry.
Remember to disconnect this RAM cable on the bottom of the laptop. This can also be accessed and disconnected from the RAM ports on the backside.
Using your fingertips, grip the edges of the motherboard to prevent damage to the circuitry.
The motherboard should lift out easily.

Place fingertips on edges of motherboard to prevent damage to the circuitry.

Remember to disconnect this RAM cable on the bottom of the laptop. This can also be accessed and disconnected from the RAM ports on the backside.

Using your fingertips, grip the edges of the motherboard to prevent damage to the circuitry.

The motherboard should lift out easily.

Step 12

Use tweezers to gently lift the tape holding down the white cable until tape is unstuck. Unthread black and white cables until free of the bottom panel.
Unscrew the Phillips #0 left side screws until left side of display is now lose.
Do the same for the two flat screws on the right side.

Use tweezers to gently lift the tape holding down the white cable until tape is unstuck. Unthread black and white cables until free of the bottom panel.

Unscrew the Phillips #0 left side screws until left side of display is now lose.

Do the same for the two flat screws on the right side.

Step 13

Display should now lift free of the main body of the Laptop.
Safely dispose of broken display and replace with new display.

Display should now lift free of the main body of the Laptop.

Safely dispose of broken display and replace with new display.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Kevin Sipple

Member since: 08/25/2022

355 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Gateway, Team 1-1, Pee Fall 2022                        

                                                  Member of Gateway, Team 1-1, Pee Fall 2022 



                    GCC-PEE-F22S1G1                     


                                            4 Members                     


                                            6 Guides authored

Better Introduction#

Introduction#

What you need#

Team#

Better Introduction

Introduction

What you need

Team