Difficulty
Moderate
Steps
10
Time Required
Suggest a time??
Sections
2
- Battery
- 2 steps
- Touchscreen
- 8 steps
Flags
0
BackAcer Aspire V5-571P-6815
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Turn off the computer and unplug all power.
Turn off the computer and unplug all power.
1024
Step 2
- Slide the locking latch to the right and hold while pulling the battery out with your other hand.
Slide the locking latch to the right and hold while pulling the battery out with your other hand.
Step 3
Touchscreen
- Insert a plastic opening tool between the screen and lid.
- Work the plastic opening tool around the perimeter while prying upwards until the screen separates from the lid.
Insert a plastic opening tool between the screen and lid.
Work the plastic opening tool around the perimeter while prying upwards until the screen separates from the lid.
Step 4
- Lay the screen flat down on the keyboard.
Lay the screen flat down on the keyboard.
Step 5
- Remove the camera using a pair of blunt nose tweezers.
- Peel up the adhesive tape keeping the camera’s cable tied down.
Remove the camera using a pair of blunt nose tweezers.
Peel up the adhesive tape keeping the camera’s cable tied down.
Step 6
- Remove the microphone from the motherboard with a pair of blunt nose tweezers.
- Slide out the adhesive tape securing the microphone cable.
Remove the microphone from the motherboard with a pair of blunt nose tweezers.
Slide out the adhesive tape securing the microphone cable.
Step 7
- Lift up the ribbon cable contained by the adhesive strip with blunt nose tweezers.
- This will allow you to access the two black digitizer ribbons.
- Use a spudger to flip up the retaining flap on the digitizer ribbon cable ZIF socket.
- Pull the ribbon cables out of their sockets.
Lift up the ribbon cable contained by the adhesive strip with blunt nose tweezers.
This will allow you to access the two black digitizer ribbons.
Use a spudger to flip up the retaining flap on the digitizer ribbon cable ZIF socket.
Pull the ribbon cables out of their sockets.
Step 8
- Remove the board from the laptop.
Remove the board from the laptop.
Step 9
- Use the blunt nose tweezers to peel up the adhesive on the display cable.
- Pull on the adhesive tape to disconnect the display from the motherboard.
Use the blunt nose tweezers to peel up the adhesive on the display cable.
Pull on the adhesive tape to disconnect the display from the motherboard.
Step 10
- Lift the whole strip connected to the circuit board and LCD connector. Place the strip to the side where it is not in contact with the screen.
- Remove the whole screen from the device.
Lift the whole strip connected to the circuit board and LCD connector. Place the strip to the side where it is not in contact with the screen.
Remove the whole screen from the device.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 4 other contributors
Brianna Sinder
Member since: 04/12/2018
377 Reputation
2 Guides authored
Badges:
10
+7 more badges
Team
UW Tacoma, Team S1-G4, Liner Spring 2018
Member of UW Tacoma, Team S1-G4, Liner Spring 2018
UWT-LINER-S18S1G4
5 Members
8 Guides authored
KaivitiSingh - Dec 1, 2021
Reply
The heading of your Procedure is “Acer Aspire V5-571P-6815 Touchscreen Replacement” BUT you just opened up the entire screen.
NOTE: you didn’t separate the “TOUCH SCREEN” from the LCD screen.
This supposed to be the most important part of your procedure item ! ! ! !
PLEASE……. *
