Difficulty
Moderate
Steps
9
Time Required
30 - 55 minutes
Sections
3
- Back Cover
- 1 step
- Battery
- 3 steps
- Speakers
- 5 steps
Flags
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackAcer Chromebook R11 C738T-C44Z
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Before you begin, make sure to shut down your laptop and drain any residual power.
What you need
Step 1
Back Cover
- Lay the laptop with the back side up.
- Use a Phillips #1 screwdriver to remove eleven 3 mm screws.
- Use the opening tool to pry the back cover off gently by placing it in the seam and working your way around the perimeter.
Lay the laptop with the back side up.
Use a Phillips #1 screwdriver to remove eleven 3 mm screws.
Use the opening tool to pry the back cover off gently by placing it in the seam and working your way around the perimeter.
1024
Step 2
Battery
- Unplug the battery connector from the motherboard. (The motherboard is a group of wires in rainbow colors)
- Use a Phillips #1 screwdriver to remove the two 3 mm screws, (one on each side of the battery), that secure it in place.
Unplug the battery connector from the motherboard. (The motherboard is a group of wires in rainbow colors)
Use a Phillips #1 screwdriver to remove the two 3 mm screws, (one on each side of the battery), that secure it in place.
Step 3
- Remove battery from its holder by pulling it upwards from the device
- Attempt to remove it as gently as possible to avoid damaging the Motherboard
Remove battery from its holder by pulling it upwards from the device
Attempt to remove it as gently as possible to avoid damaging the Motherboard
Step 4
- Install the new battery and again use a Phillips #1 screwdriver to remove the two 3 mm screws
Install the new battery and again use a Phillips #1 screwdriver to remove the two 3 mm screws
Step 5
Speakers
- Gently remove the LED Board Ribbon connected to the mother board.
Gently remove the LED Board Ribbon connected to the mother board.
Step 6
- Gently pry up speaker up using a spudger or opening tool to remove it.
- It has an adhesive, so you might have to use some force.
- Screwdrivers should not be used as prying tools and could cause damage to delicate components.
- Repeat the same process for the other speaker.
Gently pry up speaker up using a spudger or opening tool to remove it.
It has an adhesive, so you might have to use some force.
Screwdrivers should not be used as prying tools and could cause damage to delicate components.
Repeat the same process for the other speaker.
Step 7
- Use the opening tool to unplug the speaker cable from the motherboard.
- Disconnect the keyboard ribbon cable from the motherboard.
Use the opening tool to unplug the speaker cable from the motherboard.
Disconnect the keyboard ribbon cable from the motherboard.
Step 8
- Using the opening tool to unlock and disconnect the touchpad cable.
Using the opening tool to unlock and disconnect the touchpad cable.
Step 9
- Gently lift the speakers up and remove the cable from the system.
Gently lift the speakers up and remove the cable from the system.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Connie Hernandez
Member since: 09/01/2021
511 Reputation
4 Guides authored
Badges:
4
+1 more badge
Team
Gateway, Team 1-4, Saknee Fall 2021
Member of Gateway, Team 1-4, Saknee Fall 2021
GCC-SAKNEE-F21S1G4
4 Members
6 Guides authored
