Difficulty
Moderate
Steps
9
Time Required
15 minutes
Sections
3
- Back Cover
- 2 steps
- Display Screen
- 3 steps
- Microphone
- 4 steps
Flags
0
BackAcer Chromebook Spin 15 CP315-1H-P1K8
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Make sure the device is fully powered off.
- Flip the computer over so that the back is facing up.
- Remove the twelve 6mm Phillips #1 screws from the bottom of the laptop.
Make sure the device is fully powered off.
Flip the computer over so that the back is facing up.
Remove the twelve 6mm Phillips #1 screws from the bottom of the laptop.
1024
Step 2
- Use the iFixit opening tools as wedges to pry the back of the laptop off.
- Go slow, making sure not to snap the plastic. With enough of a gap made, you can use your hand to finish taking off the back.
Use the iFixit opening tools as wedges to pry the back of the laptop off.
Go slow, making sure not to snap the plastic. With enough of a gap made, you can use your hand to finish taking off the back.
Step 3
Display Screen
- Remove the five 6mm Phillips #1 screws from the hinges on either side of the laptop.
Remove the five 6mm Phillips #1 screws from the hinges on either side of the laptop.
Step 4
- Unplug the camera/microphone ribbon cable from the circuit board.
- Remove the single 3mm Phillips #1 screw from the Intel core.
- Unplug the cable from the circuit board.
Unplug the camera/microphone ribbon cable from the circuit board.
Remove the single 3mm Phillips #1 screw from the Intel core.
Unplug the cable from the circuit board.
Step 5
- Use the plastic opening tool, create a gap between the back and front of the display.
- Lift the front out with your hands.
Use the plastic opening tool, create a gap between the back and front of the display.
Lift the front out with your hands.
Step 6
Microphone
- Remove the two 3 mm Phillips #1 black screws from the microphone at the top of the display cover.
Remove the two 3 mm Phillips #1 black screws from the microphone at the top of the display cover.
Step 7
- Remove the microphone component from the rest of the computer by detaching the connected wire.
- The camera component of the laptop is connected to the same wire, so remove this as well.
- The camera is only held down with adhesives, so there is no need to use any tools.
Remove the microphone component from the rest of the computer by detaching the connected wire.
The camera component of the laptop is connected to the same wire, so remove this as well.
The camera is only held down with adhesives, so there is no need to use any tools.
Step 8
- Remove the microphone and camera wire out from around the display screen.
- Remove the ribbon cable at the bottom of the display screen to completely free the wire.
- Carefully remove the adhesive tape and take out the ribbon cable.
Remove the microphone and camera wire out from around the display screen.
Remove the ribbon cable at the bottom of the display screen to completely free the wire.
Carefully remove the adhesive tape and take out the ribbon cable.
Step 9
- Remove the microphone from the laptop.
Remove the microphone from the laptop.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Ian Sullivan
Member since: 10/29/2019
116 Reputation
1 Guide authored
Badges:
3
Team
UMass Dartmouth, Team S4-G1, Saloman Fall 2019
Member of UMass Dartmouth, Team S4-G1, Saloman Fall 2019
UMASSD-SALOMAN-F19S4G1
3 Members
5 Guides authored
