Difficulty

Difficult

Steps

14

Time Required

                          20 minutes

Sections

7

  • Back Cover
  • 2 steps
  • Battery
  • 1 step
  • Audio Jack Connector
  • 1 step
  • Camera
  • 2 steps
  • Microphone
  • 1 step
  • Logic Board
  • 3 steps
  • LCD Display
  • 4 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackAcer Iconia B1-710 / B1-711

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

Please SUBSCRIBE to my channel ツ

What you need

Video Overview

Step 1

              Back Cover
  • Switch-off the tablet.
  • Remove any SIM and/or Memory Card.
  • Start opening near to the Volume Up/Down buttons. It’s more well to use a plastic opening tool to avoid damaging the cover.
  • When lifting the cover, be careful not to tear the Loudspeaker cable at the bottom right side.
  • Disconnect the Loudspeaker cable from the Logic board.

Switch-off the tablet.

Remove any SIM and/or Memory Card.

Start opening near to the Volume Up/Down buttons. It’s more well to use a plastic opening tool to avoid damaging the cover.

When lifting the cover, be careful not to tear the Loudspeaker cable at the bottom right side.

Disconnect the Loudspeaker cable from the Logic board.

1024

Step 2

  • Before doing anything, disconnect the battery.

Before doing anything, disconnect the battery.

Step 3

              Battery
  • With a long plastic tool like a spudger, unstick the battery from the metal LCD shield.
  • Lithium Ion Battery Pack - 3.8V, 2710mAh

With a long plastic tool like a spudger, unstick the battery from the metal LCD shield.

Lithium Ion Battery Pack - 3.8V, 2710mAh

Step 4

              Audio Jack Connector
  • Unscrew 2x Philips screws
  • Disconnect and remove the Audio Jack Board flex cable.
  • Remove the board with the Audio Jack Connector.

Unscrew 2x Philips screws

Disconnect and remove the Audio Jack Board flex cable.

Remove the board with the Audio Jack Connector.

Step 5

              Camera
  • Remove the Audio jack flex cable.
  • Remove the metal plate which is placed on the camera connector.
  • Disconnect the camera flex cable.

Remove the Audio jack flex cable.

Remove the metal plate which is placed on the camera connector.

Disconnect the camera flex cable.

Step 6

  • Remove the camera.

Remove the camera.

Step 7

              Microphone
  • Remove the tape from the microphone.
  • Disconnect the Microphone wires and remove the Microphone.

Remove the tape from the microphone.

Disconnect the Microphone wires and remove the Microphone.

Step 8

              Logic Board
  • Remove the green rubber and disconnect the touch screen flex cable.
  • Disconnect the 4 coaxial antenna cables (Wi-Fi, GPS, 3G).
  • Carefully unstuck the metal folio from the LCD display flex cable.
  • Remove the 3x Phillips screws.

Remove the green rubber and disconnect the touch screen flex cable.

Disconnect the 4 coaxial antenna cables (Wi-Fi, GPS, 3G).

Carefully unstuck the metal folio from the LCD display flex cable.

Remove the 3x Phillips screws.

Step 9

  • Lift the board from the side of the battery connector and turn it around the display connector on 360 degrees.
  • Be careful for the flex cable!
  • Disconnect the LCD display flex cable.

Lift the board from the side of the battery connector and turn it around the display connector on 360 degrees.

Be careful for the flex cable!

Disconnect the LCD display flex cable.

Step 10

  • This is the Logic board.

This is the Logic board.

Step 11

              LCD Display
  • Careful unstuck the metal folio from the screen shield.
  • Remove the 4x Phillips screws.

Careful unstuck the metal folio from the screen shield.

Remove the 4x Phillips screws.

Step 12

  • lift the screen shield from one side and open it like a door, then remove it.

lift the screen shield from one side and open it like a door, then remove it.

Step 13

  • The LCD display is held from the metal screen frame by several locking clips.
  • Very careful using a tool with sharp edge, release the screen from the one side.

The LCD display is held from the metal screen frame by several locking clips.

Very careful using a tool with sharp edge, release the screen from the one side.

Step 14

  • Lift the display up and remove it.

Lift the display up and remove it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 2 other contributors 


                    ZFix

Member since: 12/09/2013

187,195 Reputation

                                      330 Guides authored                  



                       Badges:
                       35







                                                        +32 more badges

Team

                       Master Techs                        

                                                  Member of Master Techs 



                    Community                     


                                            310 Members                     


                                            1,168 Guides authored