Difficulty
Moderate
Steps
10
Time Required
15 minutes
Sections
6
- Back Cover
- 2 steps
- Battery
- 1 step
- Audio Jack Connector
- 1 step
- Camera
- 2 steps
- Microphone
- 1 step
- Logic Board
- 3 steps
Flags
1
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackAcer Iconia B1-710 / B1-711
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Please SUBSCRIBE to my channel ツ
What you need
Video Overview
Step 1
Back Cover
- Switch-off the tablet.
- Remove any SIM and/or Memory Card.
- Start opening near to the Volume Up/Down buttons. It’s more well to use a plastic opening tool to avoid damaging the cover.
- When lifting the cover, be careful not to tear the Loudspeaker cable at the bottom right side.
- Disconnect the Loudspeaker cable from the Logic board.
Switch-off the tablet.
Remove any SIM and/or Memory Card.
Start opening near to the Volume Up/Down buttons. It’s more well to use a plastic opening tool to avoid damaging the cover.
When lifting the cover, be careful not to tear the Loudspeaker cable at the bottom right side.
Disconnect the Loudspeaker cable from the Logic board.
1024
Step 2
- Before doing anything, disconnect the battery.
Before doing anything, disconnect the battery.
Step 3
Battery
- With a long plastic tool like a spudger, unstick the battery from the metal LCD shield.
- Lithium Ion Battery Pack - 3.8V, 2710mAh
With a long plastic tool like a spudger, unstick the battery from the metal LCD shield.
Lithium Ion Battery Pack - 3.8V, 2710mAh
Step 4
Audio Jack Connector
- Unscrew 2x Philips screws
- Disconnect and remove the Audio Jack Board flex cable.
- Remove the board with the Audio Jack Connector.
Unscrew 2x Philips screws
Disconnect and remove the Audio Jack Board flex cable.
Remove the board with the Audio Jack Connector.
Step 5
Camera
- Remove the Audio jack flex cable.
- Remove the metal plate which is placed on the camera connector.
- Disconnect the camera flex cable.
Remove the Audio jack flex cable.
Remove the metal plate which is placed on the camera connector.
Disconnect the camera flex cable.
Step 6
- Remove the camera.
Remove the camera.
Step 7
Microphone
- Remove the tape from the microphone.
- Disconnect the Microphone wires and remove the Microphone.
Remove the tape from the microphone.
Disconnect the Microphone wires and remove the Microphone.
Step 8
Logic Board
- Remove the green rubber and disconnect the touch screen flex cable.
- Disconnect the 4 coaxial antenna cables (Wi-Fi, GPS, 3G).
- Carefully unstuck the metal folio from the LCD display flex cable.
- Remove the 3x Phillips screws.
Remove the green rubber and disconnect the touch screen flex cable.
Disconnect the 4 coaxial antenna cables (Wi-Fi, GPS, 3G).
Carefully unstuck the metal folio from the LCD display flex cable.
Remove the 3x Phillips screws.
Step 9
- Lift the board from the side of the battery connector and turn it around the display connector on 360 degrees.
- Be careful for the flex cable!
- Disconnect the LCD display flex cable.
Lift the board from the side of the battery connector and turn it around the display connector on 360 degrees.
Be careful for the flex cable!
Disconnect the LCD display flex cable.
Step 10
- This is the Logic board.
This is the Logic board.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
ZFix
Member since: 12/09/2013
187,195 Reputation
330 Guides authored
Badges:
35
+32 more badges
Team
Master Techs
Member of Master Techs
Community
310 Members
1,168 Guides authored
