Difficulty

Moderate

Steps

16

Time Required

                          25 - 30 minutes

Sections

5

  • Back Case
  • 2 steps
  • Battery
  • 2 steps
  • Speakers
  • 3 steps
  • Power Button
  • 5 steps
  • Screen
  • 4 steps

Flags

0

  • BackAcer Iconia Tab A500

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Case
  • To start, gently separate one corner of the case using the black spudger.

To start, gently separate one corner of the case using the black spudger.

1024

Step 2

  • Once you have successfully pried the spudger in between the front case and back case, continue do so around the entire tablet until the back case is completely disconnected.

Once you have successfully pried the spudger in between the front case and back case, continue do so around the entire tablet until the back case is completely disconnected.

Step 3

              Battery
  • Remove the 5mm screws that are securing the battery to the rest of the tablet.
  • Use the Phillips #00 Screwdriver to remove the 5mm screws.

Remove the 5mm screws that are securing the battery to the rest of the tablet.

Use the Phillips #00 Screwdriver to remove the 5mm screws.

Step 4

  • Use the sharper end of the spudger to disconnect the battery from the mother board.
  • The battery connector will slide off.

Use the sharper end of the spudger to disconnect the battery from the mother board.

The battery connector will slide off.

Step 5

              Speakers
  • Locate the 4 screws and cable that hold in the two speakers.
  • Use the Phillips #1 screwdriver to remove these 2mm black screws.
  • Remove the 2mm silver screws.
  • Not all 4 screws are going to be the same kind. This will not affect the speaker replacement.

Locate the 4 screws and cable that hold in the two speakers.

Use the Phillips #1 screwdriver to remove these 2mm black screws.

Remove the 2mm silver screws.

Not all 4 screws are going to be the same kind. This will not affect the speaker replacement.

Step 6

  • Carefully remove the connector cable by pushing on the rim of black plastic insert.

Carefully remove the connector cable by pushing on the rim of black plastic insert.

Step 7

  • Unfortunately, the top speaker is a wedged under the motherboard.
  • To get this speaker out, use the spudger and gently pry it out.

Unfortunately, the top speaker is a wedged under the motherboard.

To get this speaker out, use the spudger and gently pry it out.

Step 8

              Power Button
  • Using the Phillips #1 screwdriver, remove the screws near the edges of the tablet.
  • They may be different sizes, the silver are 5mm and the black are 2mm.

Using the Phillips #1 screwdriver, remove the screws near the edges of the tablet.

They may be different sizes, the silver are 5mm and the black are 2mm.

Step 9

  • Lift up on the black flaps to release the flat cables.
  • Pull this Connector off.

Lift up on the black flaps to release the flat cables.

Pull this Connector off.

Step 10

  • Use the spudger to detach the indicated cables.
  • Remove the last motherboard screw under the rightmost cable. It is a silver 5mm.

Use the spudger to detach the indicated cables.

Remove the last motherboard screw under the rightmost cable. It is a silver 5mm.

Step 11

  • Disconnect the two gold connectors by pulling straight up on them with your fingers.
  • Like before, lift up on the black flap to detach the cable.

Disconnect the two gold connectors by pulling straight up on them with your fingers.

Like before, lift up on the black flap to detach the cable.

Step 12

  • Having disconnected all those pesky cables, the motherboard lifts cleanly out.

Having disconnected all those pesky cables, the motherboard lifts cleanly out.

Step 13

              Screen
  • Remove this components near the edge of the tablet by unscrewing the 5mm screw holding the top in place.

Remove this components near the edge of the tablet by unscrewing the 5mm screw holding the top in place.

Step 14

  • Lift the silver case, exposing the back side of the screen.

Lift the silver case, exposing the back side of the screen.

Step 15

  • Use the spudger to pry off the screen, it is held in by a film of glue around the rim.

Use the spudger to pry off the screen, it is held in by a film of glue around the rim.

Step 16

  • Swap the screen and you’re finished!

Swap the screen and you’re finished!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      7 other people completed this guide.

Author

                                      with 8 other contributors 


                    Kyle Libby

Member since: 04/07/2014

1,006 Reputation

                                      7 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Cal Poly, Team 7-23, Regan Spring 2014                        

                                                  Member of Cal Poly, Team 7-23, Regan Spring 2014 



                    CPSU-REGAN-S14S7G23                     


                                            4 Members                     


                                            19 Guides authored