Difficulty
Moderate
Steps
11
Time Required
15 minutes
Sections
2
- Battery
- 8 steps
- SSD
- 3 steps
Flags
0
BackAcer Nitro 5 AN515-53-55G9
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Make sure laptop is off and unplugged before beginning replacement.
- Flip the laptop upside down so that the bottom is facing up.
- Identify the RAM tray on the bottom of the laptop.
Make sure laptop is off and unplugged before beginning replacement.
Flip the laptop upside down so that the bottom is facing up.
Identify the RAM tray on the bottom of the laptop.
1024
Step 2
- Use the Phillips #0 screwdriver to remove the 9mm screw in the bottom left corner of the RAM tray covering.
- Remove the RAM tray cover by prying up with a spudger.
Use the Phillips #0 screwdriver to remove the 9mm screw in the bottom left corner of the RAM tray covering.
Remove the RAM tray cover by prying up with a spudger.
Step 3
- Identify the Hard Drive tray to the left side of the laptop.
- Remove screw with a #0 Philips screwdriver.
- Lift up the Slot covering using a spunger.
Identify the Hard Drive tray to the left side of the laptop.
Remove screw with a #0 Philips screwdriver.
Lift up the Slot covering using a spunger.
Step 4
- Use the Phillips #0 screwdriver to remove the 9mm screws holding the back cover in place.
- Remove the screws from the hard drive and remove it from the device.
Use the Phillips #0 screwdriver to remove the 9mm screws holding the back cover in place.
Remove the screws from the hard drive and remove it from the device.
Step 5
- Be sure you removed the hard drive. when you open the back shell and hard drive is built in this may cause damage to cable and other components.
- Carefully remove the back shell from the device working your way around all the edges.
- Do not forcefully try to separate the shell as you may cause harm to the shell.
Be sure you removed the hard drive. when you open the back shell and hard drive is built in this may cause damage to cable and other components.
Carefully remove the back shell from the device working your way around all the edges.
Do not forcefully try to separate the shell as you may cause harm to the shell.
Step 6
- Removing the back shell of the computer and it will look like this.
- The battery for the device is located at the bottom middle of the laptop at this orientation.
Removing the back shell of the computer and it will look like this.
The battery for the device is located at the bottom middle of the laptop at this orientation.
Step 7
- Locate the connector of the battery to the motherboard.
- Using your fingers, slide out the connector.
Locate the connector of the battery to the motherboard.
Using your fingers, slide out the connector.
Step 8
- Remove battery from device.
Remove battery from device.
Step 9
SSD
- Locate the SSD in the top right corner of the laptop.
Locate the SSD in the top right corner of the laptop.
Step 10
- Use the Phillips #0 screwdriver to remove the 3mm screw holding the SSD card in place.
- The SSD will pop up at an angle when the screw is removed.
Use the Phillips #0 screwdriver to remove the 3mm screw holding the SSD card in place.
The SSD will pop up at an angle when the screw is removed.
Step 11
- Slide the SSD out of its slot.
Slide the SSD out of its slot.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
9 other people completed this guide.
Author
with 6 other contributors
Rheo Bruer
Member since: 02/05/2019
931 Reputation
4 Guides authored
Badges:
15
+12 more badges
Team
Appalachian State University, Team S2-G2, Menagarishvili Spring 2019
Member of Appalachian State University, Team S2-G2, Menagarishvili Spring 2019
APSU-MENAGARISHVILI-S19S2G2
3 Members
9 Guides authored
