Difficulty

Moderate

Steps

9

Time Required

                          20 minutes

Sections

1

  • Wi-Fi Card
  • 9 steps

Flags

0

  • BackAcer Nitro 5 AN515-53-55G9

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Wi-Fi Card
  • Flip the laptop upside down so that the bottom is facing up.

Flip the laptop upside down so that the bottom is facing up.

1024

Step 2

  • Use the Phillips #0 screwdriver to remove the 9mm screw in the bottom left corner of the RAM tray covering.
  • Remove the RAM tray cover by prying it up with a plastic opening tool.

Use the Phillips #0 screwdriver to remove the 9mm screw in the bottom left corner of the RAM tray covering.

Remove the RAM tray cover by prying it up with a plastic opening tool.

Step 3

  • Remove the screw on the Hard Drive tray with a Phillips #0 screwdriver.
  • Lift up the tray covering using a plastic opening tool.

Remove the screw on the Hard Drive tray with a Phillips #0 screwdriver.

Lift up the tray covering using a plastic opening tool.

Step 4

  • Use the Phillips #0 screwdriver to remove the fourteen 9mm screws holding the back cover in place.
  • Remove the hard drive (if applicable) from the slot prior to removing the back cover.
  • This device didn’t have a hard drive so your device may look different.

Use the Phillips #0 screwdriver to remove the fourteen 9mm screws holding the back cover in place.

Remove the hard drive (if applicable) from the slot prior to removing the back cover.

This device didn’t have a hard drive so your device may look different.

Step 5

  • Carefully remove the back shell from the device by prying at the creases with a spudger around all the edges.
  • Do not forcefully try to separate the shell as you may cause harm to the shell.

Carefully remove the back shell from the device by prying at the creases with a spudger around all the edges.

Do not forcefully try to separate the shell as you may cause harm to the shell.

Step 6

  • Lift the back cover off once all the clips have been disengaged.

Lift the back cover off once all the clips have been disengaged.

Step 7

  • Using your fingers, disconnect the white and black cables connected to the left side of the Wi-fi card.

Using your fingers, disconnect the white and black cables connected to the left side of the Wi-fi card.

Step 8

  • Remove the screw holding down the Wi-Fi card with a Phillips #0 screwdriver.

Remove the screw holding down the Wi-Fi card with a Phillips #0 screwdriver.

Step 9

  • Slide the Wi-Fi card out from its port.

Slide the Wi-Fi card out from its port.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 3 other contributors 


                    Laith Williams

Member since: 09/16/2020

662 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       The Citadel Military College of South Carolina, Team S2-G11, Eggleston Fall 2020                        

                                                  Member of The Citadel Military College of South Carolina, Team S2-G11, Eggleston Fall 2020 



                    CMCSC-EGGLESTON-F20S2G11                     


                                            3 Members                     


                                            4 Guides authored

manueltopete59 - Jan 25, 2022

Reply

My hard drive got disconnected and I can’t locate where is the place to connect it