Difficulty
Moderate
Steps
17
Time Required
35 minutes
Sections
4
- Motherboard
- 8 steps
- Battery
- 1 step
- Camera
- 1 step
- Screen
- 7 steps
Flags
0
BackAcer One 10 S1002-145A
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Motherboard
- Make sure that the tablet is turned off and disconnected from any power source.
- Disconnect the tablet from the keyboard attachment.
- If you have a Micro SD card in the tablet, remove it now.
- Remove the two 3.5 mm Phillips #0 screws on either side the keyboard connection.
Make sure that the tablet is turned off and disconnected from any power source.
Disconnect the tablet from the keyboard attachment.
If you have a Micro SD card in the tablet, remove it now.
Remove the two 3.5 mm Phillips #0 screws on either side the keyboard connection.
1024
Step 2
- Starting from a corner of the tablet, use the plastic opening tool to create a gap between the screen and the back covering.
- Slowly maneuver the plastic opening tool along the perimeter of the tablet to pry the screen and back covering apart.
- Separate the back covering from the screen.
Starting from a corner of the tablet, use the plastic opening tool to create a gap between the screen and the back covering.
Slowly maneuver the plastic opening tool along the perimeter of the tablet to pry the screen and back covering apart.
Separate the back covering from the screen.
Step 3
- Peel off all of the Polyimide tape (yellow tape).
- Remove the metallic tape covering the keyboard connection.
Peel off all of the Polyimide tape (yellow tape).
Remove the metallic tape covering the keyboard connection.
Step 4
- Unscrew the two 3.5mm Phillips #0 screws and open the ZIF latch.
- Gently remove the silver part covering the battery and set it aside.
Unscrew the two 3.5mm Phillips #0 screws and open the ZIF latch.
Gently remove the silver part covering the battery and set it aside.
Step 5
- Open the ZIF (Zero Insertion Force) connectors .
- Gently remove the ribbon cables.
Open the ZIF (Zero Insertion Force) connectors .
Gently remove the ribbon cables.
Step 6
- Remove the four 4mm screws at the corners of the motherboard with the Phillips#0 bit screw.
- The screw beneath the metallic tape also needs to be removed.
Remove the four 4mm screws at the corners of the motherboard with the Phillips#0 bit screw.
The screw beneath the metallic tape also needs to be removed.
Step 7
- Disconnect the three cables on the motherboard closest to the battery.
- These cables require some extra prying power to be removed.
Disconnect the three cables on the motherboard closest to the battery.
These cables require some extra prying power to be removed.
Step 8
- Slide out the motherboard and put it aside.
Slide out the motherboard and put it aside.
Step 9
Battery
- Use the plastic opening tool to separate the glue that holds the battery to the screen.
- Avoid putting pressure on the glass while separating the battery from the screen.
- Remove the battery and set it aside.
Use the plastic opening tool to separate the glue that holds the battery to the screen.
Avoid putting pressure on the glass while separating the battery from the screen.
Remove the battery and set it aside.
Step 10
Camera
- Separate the adhesive cable from the underlying copper ribbon cable.
- Gently pry off the camera from from tablet backing.
- Remove the camera and set it aside.
Separate the adhesive cable from the underlying copper ribbon cable.
Gently pry off the camera from from tablet backing.
Remove the camera and set it aside.
Step 11
Screen
- Open the latch on the copper connector and remove it from the tablet.
Open the latch on the copper connector and remove it from the tablet.
Step 12
- Remove the three 3.5mm screws from the outside perimeter of the tablet.
Remove the three 3.5mm screws from the outside perimeter of the tablet.
Step 13
- Remove the three small latches that are underneath the screws.
Remove the three small latches that are underneath the screws.
Step 14
- Peel the silver tape on the side of the tablet using the nylon spudger. Do not completely remove the tape.
- Peel the gold tape gently. Do not completely remove the tape.
Peel the silver tape on the side of the tablet using the nylon spudger. Do not completely remove the tape.
Peel the gold tape gently. Do not completely remove the tape.
Step 15
- Locate the small green connector with the black cable attached.
- Disconnect the black cable from the small green connector using the precision tweezers.
Locate the small green connector with the black cable attached.
Disconnect the black cable from the small green connector using the precision tweezers.
Step 16
- Use a heating pack (iOpener), a hair dryer, or heat gun, and place it over the highlighted glue areas.
- This will heat up the glue beneath the tape in order to separate the LCD from the screen.
Use a heating pack (iOpener), a hair dryer, or heat gun, and place it over the highlighted glue areas.
This will heat up the glue beneath the tape in order to separate the LCD from the screen.
Step 17
- Using the nylon spudger, gently pry the LCD from the screen.
- Once separated, gently lift away the LCD from the screen.
- Place tablet screen to the side.
Using the nylon spudger, gently pry the LCD from the screen.
Once separated, gently lift away the LCD from the screen.
Place tablet screen to the side.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Shannon Griffin
Member since: 10/03/2016
1,339 Reputation
5 Guides authored
Badges:
16
+13 more badges
Team
USF Tampa, Team 1-3, Sullivan Fall 2016
Member of USF Tampa, Team 1-3, Sullivan Fall 2016
USFT-SULLIVAN-F16S1G3
4 Members
5 Guides authored
