Acer S200Hl Lcd Monitor Zif Connector Replacement Repair Guide

Difficulty

Moderate

Steps

13

Time Required

                          10 - 15 minutes            

Sections

1

• ZIF Connector
• 13 steps

Flags

0

• BackAcer S200HL LCD Monitor

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              ZIF Connector               

• Place the monitor screen face down.
• Firmly hold the base of the stand with one hand and the bottom of the monitor with the other hand.
• Pull the stand away from the monitor.

Place the monitor screen face down.

Firmly hold the base of the stand with one hand and the bottom of the monitor with the other hand.

Pull the stand away from the monitor.

1024

Step 2

• Use the plastic opening tool to pry the back panel from the front panel.
• Start at one point of the gap and pry along the entire monitor to release the clips holding the monitor together.
• There are four clips on both the left and right sides and five clips on the top and bottom.

Use the plastic opening tool to pry the back panel from the front panel.

Start at one point of the gap and pry along the entire monitor to release the clips holding the monitor together.

There are four clips on both the left and right sides and five clips on the top and bottom.

Step 3

• Gently lift the back panel away from the monitor.

Gently lift the back panel away from the monitor.

Step 4

• Unscrew the four 7.5 mm Phillips #2 screws connecting the motherboard to the metal casing.
• Be sure to keep track of where you place your screws. A magnetic mat is great for keeping your screws in one spot.

Unscrew the four 7.5 mm Phillips #2 screws connecting the motherboard to the metal casing.

Be sure to keep track of where you place your screws. A magnetic mat is great for keeping your screws in one spot.

Step 5

• Remove the four 10 mm Hex screws.

Remove the four 10 mm Hex screws.

Step 6

• Gently lift the motherboard casing from the monitor.

Gently lift the motherboard casing from the monitor.

Step 7

• The following steps give instructions for removing the three connectors shown in the picture.
• No Fuse Ribbon Cable
• ZIF Connectors
• Bundled Cable Connector

The following steps give instructions for removing the three connectors shown in the picture.

No Fuse Ribbon Cable

ZIF Connectors

Bundled Cable Connector

Step 8

• Lift the black seal to release the small ribbon connector (the No Fuss Ribbon Cable connector) from the motherboard.
• The connector will be released from the motherboard immediately.

Lift the black seal to release the small ribbon connector (the No Fuss Ribbon Cable connector) from the motherboard.

The connector will be released from the motherboard immediately.

Step 9

• Lift the black seal to release the large ribbon connector (the ZIF connector) from the motherboard.
• The connector will be released from the motherboard immediately.

Lift the black seal to release the large ribbon connector (the ZIF connector) from the motherboard.

Step 10

• Pull the bundled cable connector gently away from the motherboard.

Pull the bundled cable connector gently away from the motherboard.

Step 11

• Gently lift the motherboard to remove it from the monitor.

Gently lift the motherboard to remove it from the monitor.

Step 12

• Slowly pull the tape off of the ZIF connector and the monitor.

Slowly pull the tape off of the ZIF connector and the monitor.

Step 13

• Lift the black seal to release the ZIF connector.
• The connector will be released from the monitor immediately.

Lift the black seal to release the ZIF connector.

The connector will be released from the monitor immediately.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 7 other contributors 

                    Jeffrey Kong                     

Member since: 09/22/2014

767 Reputation

                                      5 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       Cal Poly, Team 12-3, Forte Fall 2014                        

                                                  Member of Cal Poly, Team 12-3, Forte Fall 2014 



                    CPSU-FORTE-F14S12G3                     


                                            5 Members                     


                                            5 Guides authored                     

badger - Sep 7, 2016

Reply

My model (Acer S220HQL) looks similar, but the motherboard (in its casing) was attached to the back of the screen with adhesive tape, not screws!

My problem was with the LED backlights. They often did not light up, or they switched off when I tried to alter the screen configuration (I am using it as a second monitor). Although the blue light was on, the screen went completely blank. The problem occurred with both a DVI and a D-sub connection to the PC.

After following the instructions as closely as I could, fixing the motherboard with 4 instead of 2 screws, and re-assembling, the monitor is working well. I can’t think of what problem was–maybe an earth connection was broke.

– Thanks for the instructions, they have saved my monitor until I next need to tinker with it!

Johnjoseph Villarico - Jul 8, 2020

Reply

What is the size of the dc in of the monitor?