Difficulty

Moderate

Steps

11

Time Required

                          30 minutes

Sections

3

  • Back Cover
  • 3 steps
  • Battery
  • 5 steps
  • Track Pad
  • 3 steps

Flags

2

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackAcer Spin 5 SP515-51GN-807G

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Back Cover
  • Remove the eleven 6.5 mm screws that secure the back case using a Phillips #1 screwdriver.

Remove the eleven 6.5 mm screws that secure the back case using a Phillips #1 screwdriver.

1024

Step 2

  • Use a plastic opening tool to gently pry open the back cover.

Use a plastic opening tool to gently pry open the back cover.

Step 3

  • Gently remove the back cover from the device.

Gently remove the back cover from the device.

Step 4

              Battery
  • Using tweezers, remove the piece of black tape over the battery cable connector.

Using tweezers, remove the piece of black tape over the battery cable connector.

Step 5

  • Remove the piece of black tape that covers the battery.

Remove the piece of black tape that covers the battery.

Step 6

  • Grip the battery cable on both sides with your fingertips and gently pull it away from the port.
  • If needed, use the plastic opening tool to remove the cord from its port.

Grip the battery cable on both sides with your fingertips and gently pull it away from the port.

If needed, use the plastic opening tool to remove the cord from its port.

Step 7

  • Remove the two 3.5 mm screws that secure the battery using a Phillips #00 screwdriver (PH00 bit).

Remove the two 3.5 mm screws that secure the battery using a Phillips #00 screwdriver (PH00 bit).

Step 8

  • Carefully place your fingers under the plastic lip where the screws were removed.
  • Lift upwards to remove the battery.
  • Do not bend or puncture the lithium ion battery as it poses a fire hazard.

Carefully place your fingers under the plastic lip where the screws were removed.

Lift upwards to remove the battery.

Do not bend or puncture the lithium ion battery as it poses a fire hazard.

Step 9

              Track Pad
  • Unplug the 2 ribbon cables connecting the trackpad to the motherboard by flipping up the locking tabs of the ZIF connectors and pulling out the cables.

Unplug the 2 ribbon cables connecting the trackpad to the motherboard by flipping up the locking tabs of the ZIF connectors and pulling out the cables.

Step 10

  • Remove the three 2.2 mm screws holding the trackpad in place with a Phillips #00 screwdriver.

Remove the three 2.2 mm screws holding the trackpad in place with a Phillips #00 screwdriver.

Step 11

  • Lift the lid of the laptop and push the trackpad out from the inside.

Lift the lid of the laptop and push the trackpad out from the inside.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Hikeem E Elmore

Member since: 09/17/2020

265 Reputation

                                      3 Guides authored                  



                       Badges:
                       3

Team

                       The Citadel Military College of South Carolina, Team S3-G24, Eggleston Fall 2020                        

                                                  Member of The Citadel Military College of South Carolina, Team S3-G24, Eggleston Fall 2020 



                    CMCSC-EGGLESTON-F20S3G24                     


                                            3 Members                     


                                            3 Guides authored