Difficulty
Moderate
Steps
9
Time Required
45 minutes - 1 hour
Sections
1
- Camera
- 9 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
BackAEE Mach 1
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Camera
- Take out the AEE Mach 1 and place it on a surface with its propellers facing up.
Take out the AEE Mach 1 and place it on a surface with its propellers facing up.
1024
Step 2
- Holding the base of a propeller with one hand, unscrew the propeller by hand in a clockwise direction. Complete this action on all 4 propellers.
Holding the base of a propeller with one hand, unscrew the propeller by hand in a clockwise direction. Complete this action on all 4 propellers.
Step 3
- Flip the AEE Mach 1 upside down.
- Remove the screws on the drone’s arms using a Torx T5 screwdriver.
Flip the AEE Mach 1 upside down.
Remove the screws on the drone’s arms using a Torx T5 screwdriver.
Step 4
- Gently pry open the top panel of the drone using a spudger.
- Do not completely remove the panel, as there will still be wired connections between the two halves.
- Rotate the top panel slightly to reveal the four screws beneath each propellor arm.
- Remove each of the four screws with a Phillips #0 screwdriver.
- Lift off the top panel, as it should now be free from the rest of the device.
Gently pry open the top panel of the drone using a spudger.
Do not completely remove the panel, as there will still be wired connections between the two halves.
Rotate the top panel slightly to reveal the four screws beneath each propellor arm.
Remove each of the four screws with a Phillips #0 screwdriver.
Lift off the top panel, as it should now be free from the rest of the device.
Step 5
- Using a Phillips #00 screwdriver, remove the screws from the four corners of the inner white chassis.
Using a Phillips #00 screwdriver, remove the screws from the four corners of the inner white chassis.
Step 6
- Using a Spudger (or similar tool to scrap/pry with), remove the copper foil used as tape from the sides of the chassis.
- Remove the small metal covering from the side boards.
- This can be done by hand or with the assistance of a prying tool.
Using a Spudger (or similar tool to scrap/pry with), remove the copper foil used as tape from the sides of the chassis.
Remove the small metal covering from the side boards.
This can be done by hand or with the assistance of a prying tool.
Step 7
- Using a Phillips #00 screwdriver, remove the four screws separating the side board from the white chassis.
Using a Phillips #00 screwdriver, remove the four screws separating the side board from the white chassis.
Step 8
- Using a Phillips #00 screwdriver, remove the four screws from the large motherboard on the white chassis.
- Lift the motherboard out of the case, revealing the camera cable.
Using a Phillips #00 screwdriver, remove the four screws from the large motherboard on the white chassis.
Lift the motherboard out of the case, revealing the camera cable.
Step 9
- Using the Phillips #00 screwdriver, remove the four screws holding the camera mechanism in place.
- Lift the camera assembly out of the case.
Using the Phillips #00 screwdriver, remove the four screws holding the camera mechanism in place.
Lift the camera assembly out of the case.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Cameron C Blanchard
Member since: 09/16/2020
524 Reputation
4 Guides authored
Badges:
7
+4 more badges
Team
dwsad
Member of dwsad
Community
1 Member
4 Guides authored
