Difficulty
Moderate
Steps
10
Time Required
10 minutes
Sections
4
- Back Panel
- 2 steps
- Battery
- 2 steps
- Secondary Panel
- 3 steps
- Camera
- 3 steps
Flags
0
BackAlcatel OneTouch Evolve
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Locate the access tab
- This will be an opening with enough space to insert the flat head of the plastic opening tool.
- It will be located on the bottom right of the phone
This will be an opening with enough space to insert the flat head of the plastic opening tool.
It will be located on the bottom right of the phone
1024
Step 2
Place the flat head end of the pry tool into the tab
- Rotate the pry tool 90 degrees until the panel lifts up.
- With your thumb nail, lift the rest of the panel up around the perimeter of the phone.
Rotate the pry tool 90 degrees until the panel lifts up.
With your thumb nail, lift the rest of the panel up around the perimeter of the phone.
Step 3
Identify the Battery
- This is the battery for the Alcatel One Touch Evolve. Look for this component when the back panel has been removed.
This is the battery for the Alcatel One Touch Evolve. Look for this component when the back panel has been removed.
Step 4
Removing the battery
- Place finger in the tab on the top right corner of the battery indicated by a black arrow. With slight pressure, push battery down and out of the slot until the battery is removed
Place finger in the tab on the top right corner of the battery indicated by a black arrow. With slight pressure, push battery down and out of the slot until the battery is removed
Step 5
Locate Screws Holding the Secondary Panel in Place
- There will be eight 4.5mm screws that fit your Phillips head PH00 screwdriver notated by the red circles in the image.
There will be eight 4.5mm screws that fit your Phillips head PH00 screwdriver notated by the red circles in the image.
Step 6
Remove Screws
- Unscrew each screw, counter-clockwise (left), until each one has been removed.
- If necessary, use tweezers to fully remove the screws from the device.
- Remove battery before lifting off the panel.
Unscrew each screw, counter-clockwise (left), until each one has been removed.
If necessary, use tweezers to fully remove the screws from the device.
Remove battery before lifting off the panel.
Step 7
Prying the Panel Off
- Access the small pry tool in the tool kit
- Place flat head in the crease between the phone and panel where the matte finish meets the shiny finish of the front of the phone.
- Rotate the pry tool 90 degrees until part of the panel lifts up
- All areas need to be fully risen off before the panel can be removed.
- Do not use the opening tool to pry open the device near the power button or near the volume button.
Access the small pry tool in the tool kit
Place flat head in the crease between the phone and panel where the matte finish meets the shiny finish of the front of the phone.
Rotate the pry tool 90 degrees until part of the panel lifts up
All areas need to be fully risen off before the panel can be removed.
Do not use the opening tool to pry open the device near the power button or near the volume button.
Step 8
Locate the Camera on the Device
- See yellow square for the location of the camera on the mother board.
See yellow square for the location of the camera on the mother board.
Step 9
Unclip the connection to the motherboard.
- By gently lifting the bottom rectangular piece of the camera component upwards and away from the device, the connection will come free.
- Remove the rubber casing from the camera, this piece is simply resting over the camera and can easily be removed.
By gently lifting the bottom rectangular piece of the camera component upwards and away from the device, the connection will come free.
Remove the rubber casing from the camera, this piece is simply resting over the camera and can easily be removed.
Step 10
Separate the camera from the glue patch
- Place your plastic opening tool underneath the bottom of the camera and rotate the tool to lift the camera. This will take a slight amount of force.
- You will start to see the silver sticky patch between the camera and the mother board - leave this on the mother board.
- Keep separating the camera from the sticky patch until completely removed.
- To replace camera, use the yellow lines on the motherboard as your guide.
Place your plastic opening tool underneath the bottom of the camera and rotate the tool to lift the camera. This will take a slight amount of force.
You will start to see the silver sticky patch between the camera and the mother board - leave this on the mother board.
Keep separating the camera from the sticky patch until completely removed.
To replace camera, use the yellow lines on the motherboard as your guide.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
5 other people completed this guide.
Author
with 2 other contributors
Melissa Pijoan
Member since: 10/27/2014
685 Reputation
1 Guide authored
Badges:
18
+15 more badges
Team
UMass Dartmouth, Team 4-5, Miles Fall 2014
Member of UMass Dartmouth, Team 4-5, Miles Fall 2014
UMASSD-MILES-F14S4G5
3 Members
12 Guides authored
Tina Mccraney - Aug 10, 2021
Reply
Thank you kindly for your time to write the tutorial.
