Difficulty
Easy
Steps
9
Time Required
5 minutes
Sections
4
- Back Panel
- 2 steps
- Battery
- 2 steps
- Secondary Panel
- 3 steps
- Sim Card
- 2 steps
Flags
0
BackAlcatel OneTouch Evolve
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Locate the access tab
- This will be an opening with enough space to insert the flat head of the plastic opening tool.
- It will be located on the bottom right of the phone
This will be an opening with enough space to insert the flat head of the plastic opening tool.
It will be located on the bottom right of the phone
1024
Step 2
Place the flat head end of the pry tool into the tab
- Rotate the pry tool 90 degrees until the panel lifts up.
- With your thumb nail, lift the rest of the panel up around the perimeter of the phone.
Rotate the pry tool 90 degrees until the panel lifts up.
With your thumb nail, lift the rest of the panel up around the perimeter of the phone.
Step 3
Identify the Battery
- This is the battery for the Alcatel One Touch Evolve. Look for this component when the back panel has been removed.
This is the battery for the Alcatel One Touch Evolve. Look for this component when the back panel has been removed.
Step 4
Removing the battery
- Place finger in the tab on the top right corner of the battery indicated by a black arrow. With slight pressure, push battery down and out of the slot until the battery is removed
Place finger in the tab on the top right corner of the battery indicated by a black arrow. With slight pressure, push battery down and out of the slot until the battery is removed
Step 5
Locate Screws Holding the Secondary Panel in Place
- There will be eight 4.5mm screws that fit your Phillips head PH00 screwdriver notated by the red circles in the image.
There will be eight 4.5mm screws that fit your Phillips head PH00 screwdriver notated by the red circles in the image.
Step 6
Remove Screws
- Unscrew each screw, counter-clockwise (left), until each one has been removed.
- If necessary, use tweezers to fully remove the screws from the device.
- Remove battery before lifting off the panel.
Unscrew each screw, counter-clockwise (left), until each one has been removed.
If necessary, use tweezers to fully remove the screws from the device.
Remove battery before lifting off the panel.
Step 7
Prying the Panel Off
- Access the small pry tool in the tool kit
- Place flat head in the crease between the phone and panel where the matte finish meets the shiny finish of the front of the phone.
- Rotate the pry tool 90 degrees until part of the panel lifts up
- All areas need to be fully risen off before the panel can be removed.
- Do not use the opening tool to pry open the device near the power button or near the volume button.
Access the small pry tool in the tool kit
Place flat head in the crease between the phone and panel where the matte finish meets the shiny finish of the front of the phone.
Rotate the pry tool 90 degrees until part of the panel lifts up
All areas need to be fully risen off before the panel can be removed.
Do not use the opening tool to pry open the device near the power button or near the volume button.
Step 8
Locate Sim Card
- The SIM card is located below the battery in an easy to access location.
- If there is currently no SIM card in the phone, it will be a blank area
The SIM card is located below the battery in an easy to access location.
If there is currently no SIM card in the phone, it will be a blank area
Step 9
Remove the SIM Card
- The SIM card is encased in a housing unit. In order to remove it, push left as written on the metal housing cover and it will snap loose and be able to be risen.
- Place finger on metal housing. While applying a downward force, push the finger in the direction towards the edge of the phone. An arrow also indicated this direction
- This housing case top will be on a hinge system. Put this top in the upper position and remove card with finger tips, or if necessary, tweezers.
The SIM card is encased in a housing unit. In order to remove it, push left as written on the metal housing cover and it will snap loose and be able to be risen.
Place finger on metal housing. While applying a downward force, push the finger in the direction towards the edge of the phone. An arrow also indicated this direction
This housing case top will be on a hinge system. Put this top in the upper position and remove card with finger tips, or if necessary, tweezers.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
8 other people completed this guide.
Author
with 2 other contributors
Brendan Egan
Member since: 10/28/2014
2,419 Reputation
5 Guides authored
Badges:
20
+17 more badges
Team
UMass Dartmouth, Team 4-5, Miles Fall 2014
Member of UMass Dartmouth, Team 4-5, Miles Fall 2014
UMASSD-MILES-F14S4G5
3 Members
12 Guides authored
cathyf48 - Dec 7, 2016
Reply
Easy to follow. Great help. Thank you!
james wangwa - Jun 12, 2019
Reply
Which simcard can I use for Alcatel one touch Wi-Fi in kenya?
Which sim card can I use for Alcatel one touch Wi-Fi in kenya?
JAMES OBIA - Jan 5, 2023
Reply
Thank you very much. I thought it has an inbuilt SIM at first. Some of this Model have six screw.
