Allview V Bass Firmware Update Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Allview V-Bass Firmware Update
5 steps

Flags

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

BackRéparation Allview V-Bass (Linkplay A31 FF310022)
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Since the commercial release of this speaker, Allview has not updated the firmware and application allowing the control of this speaker; thus making it inoperative for the use of Alexa online services.

The original firmware also contains a large number of security vulnerabilities (CVE-2019-15310) making their use vulnerable to attacks.

This tutorial will explain how to update the original firmware with an alternative firmware.

Disassembly of the device is not required.

What you need

Step 1

              Connection to the speaker

The first step is to connect to the web interface integrated into the speaker
If your speaker is already connected to your Wifi network, from a web browser connect to it: http:///
If your speaker is not yet connected to your wifi network, look for the speaker’s access point (by default V-Bass_xxxx) and connect to it. Once connected, the web interface will be http://10.10.10.254/

The first step is to connect to the web interface integrated into the speaker

If your speaker is already connected to your Wifi network, from a web browser connect to it: http:///

If your speaker is not yet connected to your wifi network, look for the speaker’s access point (by default V-Bass_xxxx) and connect to it. Once connected, the web interface will be http://10.10.10.254/

1024

Step 2

              Download a compatible firmware

This speaker is powered by an A31 rev 04 module built by Linkplay. The UUID number of the speaker is FF310022. Another product powered by Linkplay to the same UUID, so it is at all points identical at the material level. This is the Meet Riff marketed by theFABRIQ (ref: WB 22)
The firmware was pulbiased on 04/12/2018 and is powered by version WiiMu.4.0.6404 instead of version 3.6.4324 published on 24/04/2017
Downloaded the firmware from the linkplay update site: Fimware
Optional: Check the firmware MD5: 38f62a205a7d312520958b15599bdc3f a31dossora_new_uImage_20181204

This speaker is powered by an A31 rev 04 module built by Linkplay. The UUID number of the speaker is FF310022. Another product powered by Linkplay to the same UUID, so it is at all points identical at the material level. This is the Meet Riff marketed by theFABRIQ (ref: WB 22)

The firmware was pulbiased on 04/12/2018 and is powered by version WiiMu.4.0.6404 instead of version 3.6.4324 published on 24/04/2017

Downloaded the firmware from the linkplay update site: Fimware

Optional: Check the firmware MD5: 38f62a205a7d312520958b15599bdc3f a31dossora_new_uImage_20181204

Step 3

              Uploaded the firmware to your speaker

Go to your speaker’s website (http://10.10.10.254 when you are connected to the speaker’s AP or the speaker’s ip address on your Wifi network)
Click on “Settings”
Then on “System”
Check that your speaker is well charged, it would be a shame to have a battery failure during the update…
In “Firmware upgrade” click on choose a file, select the previously downloaded file and click on “apply”
The speaker informs you by a voice message that the update is in progress. Do not unplug your speaker!
Once the update is complete, the speaker informs you that it is completed with a voice message.

Go to your speaker’s website (http://10.10.10.254 when you are connected to the speaker’s AP or the speaker’s ip address on your Wifi network)

Click on “Settings”

Then on “System”

Check that your speaker is well charged, it would be a shame to have a battery failure during the update…

In “Firmware upgrade” click on choose a file, select the previously downloaded file and click on “apply”

The speaker informs you by a voice message that the update is in progress. Do not unplug your speaker!

Once the update is complete, the speaker informs you that it is completed with a voice message.

Step 4

              Download a compatible application

Many applications are compatible with this speaker (more than 200) (because all based on linkplay)
I have referenced the one that should work on Android here.
The most up-to-date (when writing this article) is Audio Pro Contol available for Android and Iphone

Many applications are compatible with this speaker (more than 200) (because all based on linkplay)

I have referenced the one that should work on Android here.

The most up-to-date (when writing this article) is Audio Pro Contol available for Android and Iphone

Step 5

              (Optional) Updated with Curl or the official tool

Once the update is done, the new firmware versions no longer have a WEB interface to perform a new update.
To make a new update, you must therefore go through the command line:
Retrieve the curl tool
Started a command prompt and then type the following command after having customised it (IP of the speaker, and file)
Curl -H ‘Upgrade-Insecure-Requests: 0’ -F ‘filename=@file_du_firmware’ http://<IP_DE_ENCEINTE>/cgi-bin/upload.cgi
You can also use the update tool distributed by Linkplay downloadable here (a tutorial is available in the archive file)

Once the update is done, the new firmware versions no longer have a WEB interface to perform a new update.

To make a new update, you must therefore go through the command line:

Retrieve the curl tool

Started a command prompt and then type the following command after having customised it (IP of the speaker, and file)

Curl -H ‘Upgrade-Insecure-Requests: 0’ -F ‘filename=@file_du_firmware’ http://<IP_DE_ENCEINTE>/cgi-bin/upload.cgi

You can also use the update tool distributed by Linkplay downloadable here (a tutorial is available in the archive file)

You can now use Alexa and the new services associated with your speaker!

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             


        HelloMacOS is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

HelloMacOS

Author

                                      with 1 other contributor

                    dev ngo

Member since: 12/13/2020

181 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Paultergeist22 - Dec 14, 2020

Top tuto ! enfin un moyen de mettre à jour et d’utiliser convenablement cette petite merveille qui était devenue quasi inutile à part en bluetooth.

Merci

jean Grosbois - Nov 11, 2022

Parfait, tuto excellent, permet de continuer à utiliser cet haut-parleur connecté, j’en ai acheté 2 donc je vais essayer les nouvelles applis.

Grammar Police#

Needs More Images#

Member-Contributed Guide#

Introduction#

What you need#

#

#

#

#

#

#

#

Grammar Police

Needs More Images

Member-Contributed Guide

Introduction

What you need