Altec Lansing Boomjacket 2 Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          20 minutes            

Sections

3

• Altec Lansing BoomJacket 2 Disassembly
• 6 steps
• Battery
• 2 steps
• Motherboard
• 3 steps

Flags

0

• BackAltec Lansing BoomJacket 2

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Altec Lansing BoomJacket 2 Disassembly               

• Starting from any side, use your fingers to grab the black rubber sleeve and gently pull away from the speaker on both sides.

Starting from any side, use your fingers to grab the black rubber sleeve and gently pull away from the speaker on both sides.

1024

Step 2

• Using your fingers, grab the blue sleeve from one side and pull away from the unit.

Using your fingers, grab the blue sleeve from one side and pull away from the unit.

Step 3

• At each of the marked pry spots, use the metal spudger to lift the speaker grill away from the case.
• Avoid using excessive force to prevent bending the grill.

At each of the marked pry spots, use the metal spudger to lift the speaker grill away from the case.

Avoid using excessive force to prevent bending the grill.

Step 4

• Use the tweezers to remove the six rubber stoppers. There are four in the middle and two on the sides.

Use the tweezers to remove the six rubber stoppers. There are four in the middle and two on the sides.

Step 5

• Use the PH1 Phillips screwdriver to remove the six 12mm screws that lie underneath each rubber stopper.

Use the PH1 Phillips screwdriver to remove the six 12mm screws that lie underneath each rubber stopper.

Step 6

• Gently pull apart the front panel from the base of the speaker.

Gently pull apart the front panel from the base of the speaker.

Step 7

              Battery               

• The battery will be in the middle of the speaker when the case is open.

The battery will be in the middle of the speaker when the case is open.

Step 8

• Pull firmly from both sides of the pin to disconnect the battery cable from the motherboard.
• Pull battery up and away from speaker without catching any other components.
• Motherboards have fragile components and can easily be damaged if they are hit or pulled on while extracting other parts.

Pull firmly from both sides of the pin to disconnect the battery cable from the motherboard.

Pull battery up and away from speaker without catching any other components.

Motherboards have fragile components and can easily be damaged if they are hit or pulled on while extracting other parts.

Step 9

              Motherboard               

• Disconnect the furthest right hand plug first.
• Do not pull from the wires. Pull from the white connector.

Disconnect the furthest right hand plug first.

Do not pull from the wires. Pull from the white connector.

Step 10

• Gently pull the motherboard directly upwards to avoid damage.
• Be sure to lift slowly.

Gently pull the motherboard directly upwards to avoid damage.

Be sure to lift slowly.

Step 11

• Disconnect the remaining connectors from the motherboard.
• Do not forcefully pull connectors. Pull from the connectors, not from the wires.

Disconnect the remaining connectors from the motherboard.

Do not forcefully pull connectors. Pull from the connectors, not from the wires.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.                                             

Author

                                      with 1 other contributor 

                    Zach Braaten                     

Member since: 07/12/2018

516 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges                           

Team

                       UW Tacoma, Team S1-G4, Cardinal Summer 2018                        

                                                  Member of UW Tacoma, Team S1-G4, Cardinal Summer 2018 



                    UWT-CARDINAL-SU18S1G4                     


                                            4 Members                     


                                            4 Guides authored                     

Kelvin Jasper - Oct 22, 2022

Reply

Where is the best place to purchase a motherboard for the Altec Lansing Jacket H20 4?