Amazon Fire Hdx 8 9 4Th Gen Display Daughter Board Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          8 minutes

Sections

Screen
9 steps
Display Daughterboard
3 steps

Flags

History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Screen

Ensure that the device is turned off.
Holding the device firmly, wedge a plastic opening tool between the speaker cover and the device. Then pry up to separate it from the device.
Then begin to firmly pry up the plastic cover with the plastic opening tool.
The backing is connected with adhesive so force may be necessary.
Be careful to not damage the plastic in any way.
Once you can fit your finger under the plastic cover, begin to slide your finger down the cover while simultaneously prying up.

Ensure that the device is turned off.

Holding the device firmly, wedge a plastic opening tool between the speaker cover and the device. Then pry up to separate it from the device.

Then begin to firmly pry up the plastic cover with the plastic opening tool.

The backing is connected with adhesive so force may be necessary.

Be careful to not damage the plastic in any way.

Once you can fit your finger under the plastic cover, begin to slide your finger down the cover while simultaneously prying up.

1024

Step 2

Once you reach the end of the plastic cover you should be able to completely remove it from the device.

Once you reach the end of the plastic cover you should be able to completely remove it from the device.

Step 3

Use a T5 screwdriver to remove the four 3.5 mm T5 screws at the top of the device, where the black plastic trim was located.

Use a T5 screwdriver to remove the four 3.5 mm T5 screws at the top of the device, where the black plastic trim was located.

Step 4

Release the two clear plastic clips at the top of the device near the speaker using the spudger.
Simply push down the clip with the tip of the spudger.
Push lightly to ensure that the clips aren’t damaged.

Release the two clear plastic clips at the top of the device near the speaker using the spudger.

Simply push down the clip with the tip of the spudger.

Push lightly to ensure that the clips aren’t damaged.

Step 5

Use a plastic opening tool to wedge between the screen and the device, while simultaneously holding the clip open from step 4.

Pry the screen very gently to avoid cracking the glass

Start to remove the screen from where the black plastic trim was removed and work the tool around the sides of the device. You will here small pops from the clips on the sides being released.

Step 6

Now we have to remove the two flex cables attached to both the screen assembly and body of the device.
The cable addressed in step 8 is highlighted in orange.

Now we have to remove the two flex cables attached to both the screen assembly and body of the device.

The cable addressed in step 8 is highlighted in orange.

Step 7

First turn the device 90 degrees counterclockwise.
Wedge a spudger or plastic opening tool under the black flap of the larger connector and lift up.
Pull the belt out of the connector and lift it up.

First turn the device 90 degrees counterclockwise.

Wedge a spudger or plastic opening tool under the black flap of the larger connector and lift up.

Pull the belt out of the connector and lift it up.

Step 8

Turn the device 180 degrees.
Repeat step 7 for the smaller flex cable connection.

Turn the device 180 degrees.

Repeat step 7 for the smaller flex cable connection.

Step 9

Your screen assembly has now been removed and can be replaced.

Your screen assembly has now been removed and can be replaced.

Step 10

              Display Daughterboard

We can now remove the display daughterboard.
Start by disconnecting the lone flex cable still connected to the daughterboard.

We can now remove the display daughterboard.

Start by disconnecting the lone flex cable still connected to the daughterboard.

Step 11

Turn the device 180 degrees.
Use a plastic opening tool to flip the black tab up on the connector.
Pull the flex cable out and up.

Use a plastic opening tool to flip the black tab up on the connector.

Pull the flex cable out and up.

Step 12

With a T5 screw driver remove the three 2 mm T5 screws securing the daughterboard to the device.
Use a plastic opening tool to lift up the daughterboard from the device.
The daughterboard has now been completely removed, and can be replaced.

With a T5 screw driver remove the three 2 mm T5 screws securing the daughterboard to the device.

Use a plastic opening tool to lift up the daughterboard from the device.

The daughterboard has now been completely removed, and can be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 5 other contributors

                    Jacob Rogers

Member since: 04/11/2016

285 Reputation

                                      2 Guides authored                  



                       Badges:
                       16







                                                        +13 more badges

Team

                       Cal Poly, Team 1-8, Maness Spring 2016                        

                                                  Member of Cal Poly, Team 1-8, Maness Spring 2016 



                    CPSU-MANESS-S16S1G8                     


                                            5 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team